MAX14800_09 Datasheet, PDF (2/18 Pages) Maxim Integrated Products – Low-Charge Injection, 16-Channel, High-Voltage Analog Switches

Low-Charge Injection, 16-Channel,
High-Voltage Analog Switches
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND.)
V_DD Logic-Supply Voltage .......................................-0.3V to +7V
V_PP - V_NN Supply Voltage ....................................................260V
V_PP Positive-Supply Voltage.................................-0.3V to +220V
V_NN Negative-Supply Voltage ...............................-0.3V to -220V
Logic Inputs (LE, CLR, CLK, DIN, DOUT)................-0.3V to +7V
COM_, NO_
(MAX14800/MAX14801) ...........(-0.3V + V_NN) to (V_NN + 220V)
COM_, NO_
(MAX14802/MAX14803).........(-0.3V + V_NN) to the minimum of
[(V_NN + 220V) or (V_PP + 0.3V)]
Peak Analog Signal Current Per Channel ................................3A
Continuous Power Dissipation (T_A = +70°C)
48-Pin TQFP (derate 22.7mW/°C above +70°C).........1818mW
Junction-to-Ambient Thermal Resistance (θ_JA) (Note 1)
48-Pin TQFP ..................................................................44°C/W
Junction-to-Case Thermal Resistance (θ_JC) (Note 1)
48-Pin TQFP ..................................................................10°C/W
Operating Temperature Range...............................0°C to +70°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ..................................................... +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V_DD = +2.7V to +5.5V, V_PP = +40V to V_NN + 250V, V_NN = -40V to -160V, T_A = T_MIN to T_MAX, unless otherwise noted. Typical values
are at T_A = +25°C.) (Note 2)
PARAMETER
POWER SUPPLIES
V_DD Supply Voltage
V_PP Supply Voltage
SYMBOL
V_DD
V_PP
CONDITIONS
MIN
+2.7
+40
TYP
MAX UNITS
+5.5
V
+100
V_NN +
V
250
V_NN Supply Voltage
V_DD Supply Quiescent
Current
V_NN
I_DDQ
-160
-100
0
V
5
µA
V_DD Supply Dynamic
Current
I_DD
V_DD = +5V, LE = +5V, f_CLK = 5MHz
0.5
mA
V_PP Supply Quiescent
Current
I_PPQ
All switches remain on or off, I_{COM_} = 5mA
0
10
µA
V_PP Supply Dynamic
Current (All Channel
Switching Simultaneously)
V_NN Supply Quiescent
Current
I_PP
I_NNQ
V_PP = +40V, V_NN = -160V, f_{COM_} = 50kHz
V_PP = +100V, V_NN = -100V, f_{COM_} = 50kHz
V_PP = +160V, V_NN = -40V, f_{COM_} = 50kHz
All switches remain on or off, I_{COM_} = 5mA
4
3.4
6
mA
8
0
10
µA
V_NN Supply Dynamic
Current (All Channel
Switching Simultaneously)
ANALOG SWITCH
V_PP = +40V, V_NN = -160V, f_{COM_} = 50kHz
I_NN
V_PP = +100V, V_NN = -100V, f_{COM_} = 50kHz
V_PP = +160V, V_NN = -40V, f_{COM_} = 50kHz
5
2.3
4
mA
3
COM_, NO_ Analog Signal
Range
V_{COM_},
V_{NO_}
(Note 3)
min of (V_NN
V_NN
+ 200V)
or (V_PP -
V
10V)
2 _______________________________________________________________________________________