HSI2CMOD Datasheet, PDF (2/6 Pages) Maxim Integrated Products – Evaluates: HS I2C-Compatible Parts

HS I²C-Compatible Module
Component Suppliers
SUPPLIER
PHONE
WEBSITE
Altera
Corporation
1-800-800-3753 www.altera.com
Digital Core
Design
48-32282-8266 www.digitalcoredesign.com
Fairchild
Semiconductor
1-888-522-5372
www.fairchildsemi.com
Nihon
Oscilent
Sanyo
Sumida
TDK
81-33343-3411 www.niec.co.jp
1-949-252-0522 www.oscilent.com
1-619-661-6322 www.sanyo.com
1-847-545-6700 www.sumida.com
1-847-803-6100 www.component.tdk.com
Note: Please indicate that you are using a Maxim part when
contacting these component suppliers.
Description of Hardware
HS I²C-Compatible Module Supplies
The HS I²C-compatible module requires two supplies.
The on-board 3.3V regulator requires an input voltage at
VIN of 4.5V to 24V (J3-5, J3-6). The module also requires
a regulated 5V logic supply (J3-7, J3-8). A Maxim µC
module normally provides both of these supplies.
EPM3256AQC208-10 PLD (Altera)
The EPM3256AQC208-10 is from Altera’s MAX3000A
family of PLDs. This 256 product-term device accepts
3.3V or 5V logic even when powered from a 3.3V sup-
ply. Contact Altera for any questions relating to the
PLD. See the Component Suppliers section for contact
information.
HS I²C-Compatible Module Jumpers
*The asterisks in the tables below indicate the default
configuration.
Table 1. I²C-Compatible Logic-Supply
Selection
JUMPER
JU1
SHUNT POSITION
DESCRIPTION
1-2
3.3V I²C-compatible interface
2-3*
5V I²C-compatible interface
Table 2. Crystal Oscillator Enable
JUMPER
JU2
SHUNT POSITION
DESCRIPTION
1-2*
Enable the crystal oscillator
2-3
Disable the crystal oscillator
Table 3. GPIOA
JUMPER
JU3
SHUNT POSITION
DESCRIPTION
ON
Do not use
OFF*
Disconnect GPIOA
Table 4. GPIOB
JUMPER
JU4
SHUNT POSITION
DESCRIPTION
ON
Do not use
OFF*
Disconnect GPIOB
Table 5. Global PLD Clear (GCLR)
JUMPER
JU5
SHUNT POSITION
1-2
2-3*
DESCRIPTION
Reset the PLD
Normal operation mode
Table 6. Active-High RD-Line Option
JUMPER SHUNT POSITION
DESCRIPTION
The RD line to connector J3
ON
pin 9 (J3-9) is active high;
remove U5
JU6
The RD line to connector J3
OFF*
pin 9 (J3-9) is active low; U5
must be present for proper
operation
Table 7. Active-High CS-Line Option
JUMPER
JU7
SHUNT POSITION
DESCRIPTION
The CS line to connector J3
ON
pin 11 (J3-11) is active high;
remove U6
OFF*
The CS line to connector J3
pin 11 (J3-11) is active low;
U6 must be present for
proper operation
Table 8. Active-High WR-Line Option
JUMPER
JU8
SHUNT POSITION
ON
OFF*
DESCRIPTION
The WR line to connector J3
pin 10 (J3-10) is active high;
remove U7
The WR line to connector J3
pin 10 (J3-10) is active low;
U7 must be present for
proper operation
2 ____________________________________________________