DSTINIM410 Datasheet, PDF (2/5 Pages) Maxim Integrated Products – Networked Micro Evaluation Board

DSTINIm410 Networked Microcontroller Eval Board
COMPONENT LIST (continued)
DESIGNATION QTY
DESCRIPTION
R6
1 10Ω, ±5% resistor (0805)
U1
U2, U3
1
DS80C410-FNY networked
microcontroller
2
R1LV0408CSB-7LC
512kB RAM
U4
1 AM29LV081B-70EC 1MB flash
U5, U6
2
MAX6365PKA31 reset
controller
DESIGNATION
U7
QTY
1
DESCRIPTION
MAX1792EUA18 voltage
regulator
U8
1 DS1672U-33 real-time clock
U9
1
DS2502-E48 IEEE MAC
address
Y1
1 14.7456MHz crystal
Y2
1 32kHz crystal
QUICK START
It is highly recommended that the developer use the DSTINIs400 sockets board in conjunction with the
DSTINIm410. The DSTINIs400 was specifically designed to hold the DSTINIm410 and provide the physical
interconnects (Ethernet PHY), as well as the 1-Wire, I²C, SPI™, CAN, and four serial port connectors.
If the developer wishes to implement his or her own design using the DSTINIm410, a 144-pin SODIMM connector
such as the Hirose SX6E-144S-0.8SH is required.
The DSTINIm410 must be seated correctly into the DSTINIs400 to ensure a proper connection. Insert the
DSTINIm410 into the connector at a 30-degree angle. Place index fingers behind the SODIMM connector and
place thumbs on the top edge of the DSTINIm410, pressing firmly until it clicks into place or seats with only a
millimeter of gold contact exposed. Press the DSTINIm410 down parallel to the DSTINIs400 until the side arms
latch into the center of the semicircular cutouts on the DSTINIm410.
Note that the flash used on the DSTINIm410 limits applications to a maximum of 2x clock multiplier mode with the
included 14.7456MHz crystal. Use of the 4x clock multiplier mode results in unstable operations.
FOR MORE INFORMATION
TINI platform details can be found at www.maxim-ic.com/TINI. The TINI Specification and Developer’s Guide
(Addison-Welsey, 2001) is an invaluable resource when developing with the TINI platform. Download a free copy
from our website at www.maxim-ic.com/TINIguide.
DS80C410 INFORMATION
For more information about the DS80C410 network microcontroller, refer to the DS80C410 data sheet available on
our website at www.maxim-ic.com/DS80C410.
ADDITIONAL RESOURCES
For detailed information about the initial setup and use of the TINI platform, refer to Application Note 612: Getting
Started with the TINIm400 (DS80C410) Verification Module at www.maxim-ic.com/appnoteindex.
DS80C410 Networked Microcontroller Data Sheet: www.maxim-ic.com/DS80C410
DSTINIm400 Networked Microcontroller Evaluation Board: www.maxim-ic.com/DSTINIm400
DSTINIs400/DSTINIs-00x Sockets Evaluation Board: www.maxim-ic.com/DSTINIs400
Microcontroller Website: www.maxim-ic.com/microcontrollers
SPI is a trademark of Motorola Inc.
2 of 5
Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.
No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2006 Maxim Integrated Products
The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.