 English |
|
|
|
|
|
|
|
| DG406 Datasheet, PDF (2/12 Pages) Intersil Corporation – Single 16-Channel/Differential 8-Channel, CMOS Analog Multiplexers | |||
| |||
| ◁ |
Improved, 16-Channel/Dual 8-Channel,
CMOS Analog Multiplexers
ABSOLUTE MAXIMUM RATINGS
Voltage Referenced to V-
V+ ............................................................................-0.3V, 44V
GND .........................................................................-0.3V, 25V
Digital Inputs, S, D (Note 1)....................(V- - 2V) to (V+ + 2V) or
30mA (whichever occurs first)
Continuous Current (any terminal) ......................................30mA
Peak Current, S or D
(pulsed at 1ms, 10% duty cycle max) ..........................100mA
Continuous Power Dissipation (TA = +70°C)
Plastic DIP (derate 9.09mW/°C above +70°C) ............727mW
Wide SO (derate 12.50mW/°C above +70°C)............1000mW
PLCC (derate 10.53mW/°C above +70°C) ..................842mW
CERDIP (derate 16.67mW/°C above +70°C) .............1333mW
Operating Temperature Ranges
DG406/DG407C_ ...............................................0°C to +70°C
DG406/DG407D_ ............................................-40°C to +85°C
DG406/DG407AK ..........................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Note 1: Signals on S_, D_, A0, A1, A2, A3, or EN exceeding V+ or V- are clamped by internal diodes. Limit forward current to max-
imum current ratings.
Stresses beyond those listed under âAbsolute Maximum Ratingsâ may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICSâDual Supplies
(V+ = 15V, V- = -15V, GND = 0V, VAH = +2.4V, VAL = +0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX
(Note 2)
SWITCH
Analog Signal Range
VANALOG (Note 3)
-15
15
Drain-Source On-Resistance rDS(ON)
IS = -1.0mA,
VD = ±10V
TA = +25°C
TA = TMIN to TMAX
60 100
125
On-Resistance Matching
Between Channels
ârDS(ON)
IS = -1.0mA,
VD = ±10V (Note 4)
TA = +25°C
TA = TMIN to TMAX
1.5
8
10
On-Resistance Flatness
rFLAT
IS = -1.0mA,
VD = ±5V or 0V
TA = +25°C
TA = TMIN to TMAX
1.8
9
12
Source-Off Leakage Current
(Note 5)
IS(OFF)
VD = +10V,
VS = ±10V,
VEN = 0V
TA = +25°C
TA = TMIN C, D
to TMAX
A
-0.5 0.01 0.5
-5
5
-50
50
Drain-Off Leakage Current
(Note 5)
ID(OFF)
VD = ±10V,
VS = +10V,
VEN = 0V
VD = +10V,
VS = ±10V,
VEN = 0V
DG406
DG407
TA = +25°C
TA = TMIN C, D
to TMAX
A
TA = +25°C
TA = TMIN C, D
to TMAX
A
-1 0.02 1
-40
40
-200
200
-1 0.02 1
-20
20
-100
100
TA = +25°C
-1 0.02 1
Drain-On Leakage Current
(Note 5)
ID(ON)
+
IS(ON)
VD = ±10V,
VS = ±10V,
sequence
each switch
on
DG406
DG407
TA = TMIN C, D
to TMAX
A
TA = +25°C
TA = TMIN C, D
to TMAX
A
-40
40
-200
200
-1 0.02 1
-20
20
-100
100
UNITS
V
â¦
â¦
â¦
nA
nA
nA
2 _______________________________________________________________________________________
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese