MAX15022 Datasheet, PDF (16/27 Pages) Maxim Integrated Products – Dual, 4A/2A, 4MHz, Step-Down DC-DC Regulator with Dual LDO Controllers

Dual, 4A/2A, 4MHz, Step-Down DC-DC
Regulator with Dual LDO Controllers
Use the following equation to calculate the input ripple
when only one regulator is enabled:
I_CIN(RMS)[A] = I_LOAD(MAX)[A] ×
( ) ^VOUT_^{[V] × V}PVIN_ ^{− V}OUT_ ^[V]
V_{PVIN_} [V]
The MAX15022 includes UVLO hysteresis to avoid possi-
ble unintentional chattering during turn-on. Use additional
bulk capacitance if the input source impedance is high. If
using a lower input voltage, additional input capacitance
helps to avoid possible undershoot below the undervolt-
age lockout threshold during transient loading.
Output-Capacitor Selection
The allowed output-voltage ripple and the maximum
deviation of the output voltage during load steps deter-
mine the required output capacitance and its ESR. The
output ripple is mainly composed of ΔV_Q (caused by
the capacitor discharge) and ΔV_ESR (caused by the
voltage drop across the equivalent series resistance of
the output capacitor). The equations for calculating the
output capacitance and its ESR are:
C_OUT [μF]
=
8×
ΔI_P−P [A]
ΔV_Q[V]× f_SW
[MHz]
ESR[mΩ] = ^{2 × ΔVESR [mV]}
ΔI_P−P [A]
where ΔI_P-P is the peak-to-peak inductor current, and
f_SW is the switching frequency.
ΔV_ESR and ΔV_Q are not directly additive since they are
out of phase from each other. If using ceramic capaci-
tors, which generally have low ESR, ΔV_Q dominates. If
using electrolytic capacitors, ΔV_ESR dominates.
The allowable deviation of the output voltage during
fast load transients also affects the output capacitance,
its ESR, and its equivalent series inductance (ESL). The
output capacitor supplies the load current during a
load step until the controller responds with an
increased duty cycle. The response time (t_RESPONSE)
depends on the gain bandwidth of the controller (see
the Compensation-Design Guidelines section). The
resistive drop across the output capacitor’s ESR
(ΔV_ESR), the drop across the capacitor’s ESL (ΔV_ESL),
and the capacitor discharge (ΔV_Q) causes a voltage
droop during the load-step (I_STEP). Use a combination
of low-ESR tantalum/aluminum electrolyte and ceramic
capacitors for better load transient and voltage ripple
performance. Non-leaded capacitors and capacitors in
parallel help reduce the ESL. Keep the maximum out-
put-voltage deviation below the tolerable limits of the
electronics being powered.
Use the following equations to calculate the required
output capacitance, ESR, and ESL for minimal output
deviation during a load step:
ESR[mΩ] = ^{ΔVESR [mV]}
I_STEP [A]
C_OUT
[μF]
=
I_STEP
[A]
× t_RESPONSE
ΔV_Q [V]
[μs]
ESL[nH] = ^{ΔVESL[mV]× tSTEP[μs]}
I_STEP [A]
where I_STEP is the load step, t_STEP is the rise time of the
load step, and t_RESPONSE is the response time of the
controller.
Compensation Design Guidelines
The MAX15022 uses a fixed-frequency, voltage-mode
control scheme that regulates the output voltage by
comparing the output voltage against a fixed reference.
The subsequent “error” voltage that appears at the
error-amplifier output (COMP_) is compared against an
internal ramp voltage to generate the required duty
cycle of the PWM. A second order lowpass LC filter
removes the switching harmonics and passes the DC
component of the PWM signal to the output. The LC fil-
ter has an attenuation slope of -40dB/decade and intro-
duces 180° of phase shift at frequencies above the LC
resonant frequency. This phase shift in addition to the
inherent 180° of phase shift of the regulator’s negative
feedback system turns the feedback into unstable posi-
tive feedback. The error amplifier and its associated
circuitry must be designed to achieve a stable closed-
loop system.
The basic controller loop consists of a power modulator
(comprised of the regulator’s PWM, associated circuitry,
and LC filter), an output feedback divider, and an error
amplifier. The power modulator has a DC gain set by
V_AVIN/V_RAMP where the ramp voltage (V_RAMP) is a func-
tion of the V_AVIN and results in a fixed DC gain of 4V/V,
providing effective feed-forward compensation of input-
voltage supply DC variations. The feed-forward com-
pensation eliminates the dependency of the power mod-
ulator’s gain on the input voltage such that the feedback
compensation of the error amplifier requires no modifi-
cations for nominal input-voltage changes. The output
filter is effectively modeled as a double-pole and a sin-
gle zero set by the output inductance (L), the DC resis-
tance of the inductor (DCR), the output capacitance
(C_OUT), and its equivalent series resistance (ESR).
16 ______________________________________________________________________________________