MAX6456UT16S-T Datasheet, PDF (1/11 Pages) Maxim Integrated Products – Supervisors with Separate VCC Reset and Manual Reset Outputs

19-2637; Rev 3; 6/10
µP Supervisors with Separate V_CC Reset and
Manual Reset Outputs
General Description
The MAX6453–MAX6456 are low-power, dual-voltage
µP supervisors featuring separate V_CC reset and manu-
al reset outputs. The dual outputs support both soft-
system reset (interrupt) and hard-system reset (reboot)
functions. The reset output asserts when any of the
monitored voltages falls below its specified threshold
and remains asserted for the reset timeout (140ms min)
after all voltages exceed their respective reset thresh-
olds. All devices are offered with nine factory-fixed
reset thresholds for monitoring primary system voltages
(V_CC) from 1.8V to 5V and an adjustable reset input for
monitoring a secondary system voltage down to 0.63V.
Each device has a manual reset input, a V_CC reset out-
put, and a manual reset output. The MAX6453/
MAX6454 manual reset output asserts when the manual
reset input is low. It remains asserted for the manual
reset timeout period (140ms min) after the manual reset
input transitions high. The MAX6453/MAX6354 manual
reset input controls only the manual reset output and
does not affect the V_CC reset output.
The manual reset input of the MAX6455/MAX6456 con-
trols both the manual reset and V_CC reset outputs. When
the manual reset input is low for less than the extended
setup timeout period, only the manual reset output
asserts and remains asserted for the manual reset time-
out period (140ms min) after the manual reset input tran-
sitions high. If the manual reset input is low for at least
the extended setup timeout period, the reset output also
asserts and remains asserted for the reset timeout peri-
od (140ms min) after the manual reset input transitions
high. This enhanced feature allows the implementation of
a soft/hard-system reset combination.
The MAX6453/MAX6455 have active-low, push-pull
reset and manual reset outputs, and the MAX6454/
MAX6456 have active-low, open-drain reset and manu-
al reset outputs. All devices are available in small
SOT23-6 packages and are fully specified over the
extended temperature range (-40°C to +85°C).
Applications
Set-Top Boxes
Consumer Electronics
DVD Players
Cable/DSL Modems
MP3 Players
Industrial Equipment
Automotive
Medical Devices
Features
♦ Precision Factory-Set Reset Thresholds From
1.6V to 4.6V
♦ Adjustable Threshold to Monitor Voltages Down
to 0.63V
♦ Manual Reset Input with Extended Setup Period
♦ Immune to Short Voltage Transients
♦ Low 6µA Supply Current
♦ Guaranteed Valid Reset Down to V_CC = 1.0V
♦ Active-Low RESET (Push-Pull or Open-Drain)
Outputs
♦ 140ms (min) Reset Timeout Period
♦ Small SOT Package
Ordering Information
PART
TEMP RANGE PIN-PACKAGE
MAX6453UT_ _ _-T -40°C to +85°C 6 SOT23
MAX6454UT_ _ _-T -40°C to +85°C 6 SOT23
MAX6455UT_ _ _-T -40°C to +85°C 6 SOT23
MAX6456UT_ _ _-T -40°C to +85°C 6 SOT23
Note: The first “_ _” is a placeholder for the threshold voltage
level of the devices. A desired threshold level is set by the part
number suffix found in Table 1. The third “_” is a placeholder for
the manual reset setup period of the devices. A desired setup
period is set by the letter suffix found in Table 2. All devices are
available in tape-and-reel only. There is a 2500-piece minimum
order increment for standard versions (Table 2). Sample stock
is typically held on standard versions only. Nonstandard ver-
sions require a minimum order increment of 10,000 pieces.
Contact factory for availability.
Devices are available in both leaded and lead(Pb)-free packaging.
Specify lead-free by replacing “-T” with “+T” when ordering.
Selector Guide appears at end of data sheet.
Pin Configurations
TOP VIEW
RESET 1
6 MR RESET 1
6 MR
MAX6453
MAX6455
GND 2 _MAX6454 5 RSTIN GND 2 _MAX6456 5 RSTIN
MROUT 3
4 V_CC MROUT 3
4 V_CC
SOT23-6
SOT23-6
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.