MAX2410_1 Datasheet, PDF (1/8 Pages) Maxim Integrated Products – Evaluation Kit

19-1320; Rev 1; 3/98
MAX2410 Evaluation Kit
________________General Description
The MAX2410 evaluation kit (EV kit) simplifies testing of the
MAX2410. This EV kit allows evaluation of the MAX2410’s
low-noise amplifier (LNA), receive downconverter
mixer, transmit upconverter mixer, variable-gain power-
amplifier (PA) driver, and power-management features.
____________________Component List
DESIGNATION QTY
DESCRIPTION
C1, C2
2 47pF ceramic capacitors, 0603 size
C3
1
10µF tantalum capacitor
AVX TAJC106K016
C4, C5,
C6, C8
4 0.1µF ceramic capacitors, 0805 size
C7, C10, C11,
C16, C17, 7
C19, C20
220pF ceramic capacitors, 0805 size
C9, C15, C18,
C23, C24
5
1000pF ceramic capacitors, 0805 size
C12, C14,
C22, C25, C26
0
Not installed
C21
1 1pF ceramic capacitor, 0805 size
L1
1
18nH inductor, 0805 size
Coilcraft 0805CS-180XMBC
L2
1
5.6nH inductor, 0805 size
Taiyo Yuden HK16085N6S
L3, L12
2
68nH inductors, 0805 size
Coilcraft 0805CS-680XKBC
L4, L5
L6, L7, L9
2 0Ω resistors, 0805 size
0 Not installed
L8, L13
2
3.9nH inductors, 0805 size
Taiyo Yuden HK16083N9S
L11
1
82nH inductor, 0805 size
Coilcraft 0805CS-820XKBC
R1, R2, R3 3 1kΩ resistors, 0805 size
LNAIN,
LNAOUT, IFIN,
IFOUT, LO,
PADRIN,
8
PADROUT,
TXMXOUT
SMA edge-mount connectors
RXMXIN
1 SMA PC-mount connector
RXEN, TXEN,
VGC
3
3-pin headers
VCC, GND 2 2-pin headers
U1
1 MAX2410EEI 28-pin QSOP
____________________________Features
o +2.7V to +5.5V Single-Supply Operation
o 50Ω SMA Inputs and Outputs on RF and IF Ports
o Allows Testing of Shutdown Mode
o Fully Assembled and Tested
_______________Ordering Information
PART
MAX2410EVKIT
TEMP. RANGE
-40°C to +85°C
IC-PACKAGE
28 QSOP
______________Component Suppliers
SUPPLIER
AVX
Coilcraft
Taiyo Yuden
USA
PHONE
INTERNET
[phone]
[phone] FAX
http://www.avxcorp.com
[phone]
[phone] FAX
http://www.coilcraft.com
[phone]
[phone] FAX
http://www.t-yuden.com
_________________________Quick Start
The MAX2410 EV kit is fully assembled and factory test-
ed. Follow these instructions for initial evaluation of the
MAX2410.
Test Equipment Required
This section lists the recommended test equipment to
verify operation of the MAX2410. It is intended as a
guide only, and some substitutions may be possible.
• Two RF signal generators capable of delivering at
least 0dBm of output power up to 2GHz (HP8648C,
or equivalent).
• An RF spectrum analyzer that covers the operating
frequency range of the MAX2410 as well as a few
harmonics (HP8561E, for example).
• A power supply which can provide up to 100mA at
+2.7V to +5.5V.
• A voltage source (0V to 5V) for adjusting the gain-
control (GC) voltage on the PA driver.
• An optional ammeter for measuring the supply cur-
rent.
• Several 50Ω SMA cables.
________________________________________________________________ Maxim Integrated Products 1
For free samples & the latest literature: http://www.maxim-ic.com, or phone [phone].
For small orders, phone [phone].