|
MAX2031_1 Datasheet, PDF (1/7 Pages) Maxim Integrated Products – Evaluation Kit | |||
|
19-3810; Rev 0; 8/05
MAX2031 Evaluation Kit
General Description
The MAX2031 evaluation kit (EV kit) simplifies the evalua-
tion of the MAX2031 WCDMA, cdma2000®, GSM, and
WiMAX(SM) base-station up/downconversion mixer. It is
fully assembled and tested at the factory. Standard 50â¦
SMA connectors are included on the EV kitâs input and
output ports to allow quick and easy evaluation on the
test bench.
This document provides a list of test equipment required
to evaluate the device, a straightforward test procedure
to verify functionality, a description of the EV kit circuit,
the circuit schematic, a bill of materials (BOM) for the kit,
and artwork for each layer of the PC board.
Ordering Information
PART
MAX2031EVKIT
TEMP RANGE
-40°C to +85°C
IC PACKAGE
20 Thin QFN-EP*
*EP = Exposed paddle.
WiMAX is a service mark of Broadband.com, Inc.
cdma2000 is a registered trademark of Telecommunications
Industry Association.
DESIGNATION QTY
DESCRIPTION
C1, C2, C7, C8,
C10, C11, C12
82pF ±5% 50V C0G ceramic
7 capacitors (0603)
Murata GRM1885C1H820J
C3, C6, C9
0.01µF ±10%, 50V X7R ceramic
3 capacitors (0603)
Murata GRM188R71H103K
6.0pF ±0.25pF, 50V C0G ceramic
C4
1
capacitor (0603)
Murata GRM1885C1H6R0C
(used for upconverter operation)
2.0pF ±0.1pF, 50V C0G ceramic
capacitor (0603)
C5
0 Murata GRM1885C1H2R0B
(not installedâused for
downconverter operation)
J1âJ4
PC board edge-mount SMA RF
4
connectors
(flat-tab launch)
Johnson 142-0741-856
4.7nH ±0.3nH inductor (0603)
L1
1 TOKO LL1608-FS4N7S
(used for upconverter operation)
R1
1 523⦠±1% resistor (0603)
Features
o Fully Assembled and Tested
o 50⦠SMA Connectors on Input and Output Ports
o 815MHz to 1000MHz RF Frequency Range
o 960MHz to 1180MHz LO Frequency Range
o DC to 250MHz IF Frequency Range
o 7dB Conversion Loss
o +36dBm Input IP3
o +27dBm Input 1dB Compression Point
o 7dB Noise Figure
o Integrated LO Buffer
o Integrated RF and LO Baluns
o Low -3dBm to +3dBm LO Drive
o Built-In SPDT LO Switch with 49dB LO1 to LO2
Isolation and 50ns Switching Time
o External Current-Setting Resistor Provides Option
for Operating Mixer in Reduced Power/Reduced
Performance Mode
Component List
DESIGNATION QTY
DESCRIPTION
R2
1 47k⦠±5% resistor (0603)
T1
1
1:1 transformer (50:50)
M/A-COM MABAES0029
Large test point for 0.062in PC board
TP1
1 (red)
Mouser 151-107 or equivalent
Large test point for 0.062in PC board
TP2
1 (black)
Mouser 151-103 or equivalent
Large test point for 0.062in PC board
TP3
1 (white)
Mouser 51-101 or equivalent
Active mixer IC (5mm x 5mm 20-pin
thin QFN exposed paddle)
Maxim MAX2031ETP
NOTE: U1 HAS AN EXPOSED
U1
1
PADDLE CONDUCTOR THAT
REQUIRES IT TO BE SOLDER
ATTACHED TO A GROUNDED
PAD ON THE CIRCUIT BOARD
TO ENSURE A PROPER
ELECTRICAL/THERMAL DESIGN.
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maximâs website at www.maxim-ic.com.
|
▷ |