TLD1125EL_15 Datasheet, PDF (16/36 Pages) Marl International Limited – Basic LED Driver

TLD1125EL
PWMI Pin
Electrical Characteristics Internal Supply / EN / PWMI pin (cont’d)
Unless otherwise specified: V_S = 5.5 V to 40 V, T_j = -40 °C to +150 °C, R_SET = 12 kΩ all voltages with respect to
ground, positive current flowing into pin for input pins (I), positive currents flowing out of the I/O and output pins
(O) (unless otherwise specified)
Pos. Parameter
Symbol
Limit Values
Unit Conditions
6.3.3 Current consumption,
device disabled via ST
I_S(dis,ST)
Min. Typ.
–
–
–
–
–
–
6.3.4
Current consumption,
I_{S(dis,IN_SET)}
device disabled via IN_SET
–
–
–
–
–
–
6.3.5
Current consumption,
I_S(dis,PWMI)
device disabled via PWMI
–
–
–
–
–
–
6.3.6
Current consumption,
active mode in fault
I_S(fault,STu)
detection condition with ST-
pin unconnected
–
–
–
–
–
–
6.3.7
Current consumption,
active mode in fault
I_S(fault,STG)
detection condition with ST-
pin connected to GND
6.3.8 Power-on reset delay time ³⁾ t_POR
–
–
–
–
–
–
–
–
Max.
1.4
0.65
1.4
mA ²⁾ V_S = 18 V
T_j < 105 °C
V_ST = 5 V
V_EN = 5.5 V
V_EN = 18 V
1) _{REN = 10 kΩ between}
VS and EN-pin
mA ²⁾ V_S = 18 V
T_j < 105 °C
V_{IN_SET} = 5 V
1.4
V_EN = 5.5 V
0.7
V_EN = 18 V
1.4
1) _{REN = 10 kΩ between}
VS and EN-pin
1.6
0.75
1.6
mA ²⁾ V_S = 18 V
T_j < 105 °C
V_PWMI= 3.4 V
V_EN = 5.5 V
V_EN = 18 V
1) _{REN = 10 kΩ between}
VS and EN-pin
mA ²⁾ V_S = 18 V
T_j < 105 °C
R_SET = 12 kΩ
V_PWMI= 0.5 V
V_OUT = 18 V or 0 V
1.7
V_EN = 5.5 V
1.1
V_EN = 18 V
1.8
1) _{REN = 10 kΩ between}
VS and EN-pin
mA ²⁾ V_S = 18 V
T_j < 105 °C
R_SET = 12 kΩ
V_PWMI= 0.5 V
V_OUT = 18 V or 0 V
V_ST = 0 V
6.0
V_EN = 5.5 V
4.9
V_EN = 18 V
5.9
1) _{REN = 10 kΩ between}
VS and EN-pin
25
µs
1) _{VS = VEN = 0 → 13.5 V}
V_OUT(nom) = 3.6 ± 0.3V
I_OUT = 80% I_OUT(nom)
Data Sheet
16
Rev. 1.0, 2013-08-08