EZ290_15 Datasheet, PDF (2/5 Pages) Marktech Corporate – Gen II LEDs

Maximum Ratings at T_A = 25°C ^{Notes 1&3}
DC Forward Current
Peak Forward Current (1/10 duty cycle @ 1 kHz)
LED Junction Temperature
Reverse Voltage
Operating Temperature Range
Storage Temperature Range
Electrostatic Discharge Threshold (HBM) ^{Note 2}
Electrostatic Discharge Classification (MIL-STD-883E) ^{Note 2}
CxxxEZ290-Sxx00-2
50 mA
100 mA
125°C
5V
-40°C to +100°C
-40°C to +100°C
1000 V
Class 2
Typical Electrical/Optical Characteristics at T_A = 25°C, If = 20 mA ^{Note 3}
Part Number
Forward Voltage (V_f, V)
C460EZ290-Sxx00-2
C470EZ290-Sxx00-2
C527EZ290-Sxx00-2
Min.
2.7
2.7
2.9
Typ.
3.1
3.1
3.2
Max.
3.7
3.7
3.9
Reverse Current
[I(Vr=5V), μA]
Max.
2
2
2
Full Width Half Max
(λ_D, nm)
Typ.
21
22
35
Mechanical Specifications
Description
P-N Junction Area (μm)
Top Area (μm)
Bottom Area (μm)
Chip Thickness (μm)
Au Bond Pad Diameter (μm)
Au Bond Pad Thickness (μm)
Back Contact Metal Area (μm)
Back Contact Metal Thickness (μm) ^{Note 4}
CxxxEZ290-Sxx00-2
Dimension
Tolerance
226 x 226
± 25
280 x 280
± 25
280 x 280
± 25
170
± 25
100
-15, +5
3.0
± 1.0
280 x 280
± 25
3.0
± 0.3
Notes:
1. Maximum ratings are package dependent. The above ratings were determined using a T-1 3/4 package (with Hysol OS4000
epoxy) for characterization. Ratings for other packages may differ. The forward currents (DC and Peak) are not limited by the die
but by the effect of the LED junction temperature on the package. The junction temperature limit of 125°C is a limit of the T-1
3/4 package; junction temperature should be characterized in a specific package to determine limitations. Assembly processing
temperature must not exceed 325°C (<5 seconds).See Cree EZBright Applications Note for assembly process information.
2. Product resistance to electrostatic discharge (ESD) according to the HBM is measured by simulating ESD using a rapid avalanche
energy test (RAET). The RAET procedures are designed to approximate the maximum ESD ratings shown. The RAET procedure is
performed on each die. The ESD classification of Class 2 is based on sample testing according to MIL-STD-883E.
3. All products conform to the listed minimum and maximum specifications for electrical and optical characteristics when assembled
and operated at 20 mA within the maximum ratings shown above. Efficiency decreases at higher currents. Typical values given
are within the range of average values expected by manufacturer in large quantities and are provided for information only. All
measurements were made using lamps in T-1 3/4 packages (with Hysol OS4000 epoxy). Optical characteristics measured in an
integrating sphere using Illuminance E.
4. Specifications are subject to change without notice.
Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree
logo and EZBright are registered trademarks, and EZ, EZ290, EZ-08, EZ-18 and EZ-21 are trademarks of Cree, Inc.
2
CPR3EJ Rev -
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: [phone]
www.cree.com