60654-1 Datasheet, PDF (71/76 Pages) Tyco Electronics – Machine Applied Terminations, Open Barrel Terminals

Machine Applied Terminations, Open Barrel Terminals
(Rings, Spades, Pins, Receptacles, Splices, Tabs)
Application Tooling (Continued)
AMPOMATOR CLS IV+
Lead-Making Machines, 356500-1, -2
Fully-automatic machines
that measure, cut, strip
and terminate single leads.
Microprocessor-controlled,
and programmed and
operated using an easy-to-
follow, menu-driven touch-
screen. Features include
direct-drive terminating
units with precision crimp
height adjustment, fully
programmable setups, wire
runout and splice detection,
and motorized pre-feed with
wire straightener. Crimp
Quality Monitoring is also
available.
Specifications
Width — 159 [4 040]
Depth — 68 [1 730]
Height — 86 [2 185] with
24 [610] dia. reel
Weight — 2 000 lb [907 kg]
Electrical — 220 VAC, 50 or
60 Hz, single phase, 25 A, with
neutral and ground
Air — 90 psi [6.21 bar], 15 scfm
[0.0071 m³/s] sustained
Wire Range — 26-10 AWG
[0.12-6 mm²] stranded, 26-16 AWG
[0.12-1.4 mm²] solid
Lead Lengths — 3-90 [76.2-2 285],
90-1 000 [2 285-25 400] with long
lead conveyors
For more information, request Catalog
124324.
Applicators
End- and Side-Feed
Heavy-Duty Miniature
(HDM) Applicators
Tyco Electronics applicators
are designed to exacting
specifications to produce
consistent, high-quality
terminations.
HDM applicators are
quickly interchangeable
and easily repaired. They
feature simple dial-in set-
tings for adjusting crimp
height for terminating differ-
ent wire combinations within
the designated CMA range.
These applicators are used
with both bench machines
and fully-automatic lead
makers. They can also be
used for crimp quality
monitoring on systems
equipped with the CQM
G-Adapter. Call the
Tooling Assistance Hotline
at 1-800-722-1111 for
further information.
Catalog 82227
Revised 8-04
www.tycoelectronics.com
Standard (STD) Applicators
Standard style applicators
are generally used for long
production runs using
dedicated equipment, or
when splicing a coil, for
example, that needs to
be positioned close to
the crimping area in the
applicator. The crimp height
can be adjusted by raising
or lowering the base mount.
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Standard Style Applicator
for Large CMA Splice,
Part Number 566372-2
This applicator was
designed specifically to
apply AMP 5 000-16 000
CMA Splice, Part Number
63625-1. It features a
highly-visible, close-up
crimp area—less than 1
[25] from the front of the
guard. You can easily
splice multiple wires by
simply rotating them down
through the front of the
guard into the crimp area.
It is an air-feed applicator,
and can be used with
AMP-O-LECTRIC Model K
termination machine Part
Number 1-471273-2 or
1-471273-3.
71
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967