1-1658526-5 Datasheet, PDF (71/100 Pages) Tyco Electronics – Ribbon Cable Connector Selection Guide

Ribbon Cable Interconnect Solutions
Comparison of R-CAM 2A, R-CAM 3A and R-CAM 4
Machine Model
R-CAM 2A
R-CAM 3A
R-CAM 4
Part Number*
760700-K
761900-K
318800-K
Cable Size
28 AWG [0.08 mm²],
.050 [1.27] centerline
28 AWG [0.08 mm²],
.050 [1.27] centerline
28 AWG [0.08 mm²],
.050 [1.27] centerline and
30 AWG [0.05 mm²],
.025 [0.64] centerline
Maximum cable length of 48 [1 220]
Maximum cable length of 105 [2 665] Maximum cable length of 100 [2 540]
Cable Assembly
Configurations
(Refer to page 73)
Produces one- to four-connector assem-
blies with unterminated tail lengths up to
12 [305]
Produces one- or two-connector assem-
blies with unterminated tail lengths up to
24 [610]
Produces one- to 10-connector assem-
blies with unterminated tail lengths up to
24 [610]
Trailing connectors can be oriented up or Trailing connectors can be oriented up or Trailing connectors can be oriented up or
down
down
down
Automatically processes and tests
—
—
assemblies produced with pre-
manufactured slit-and-twist cable
Production Rates
(Refer to page 72)
Size
Depending on cable lengths, can apply
and test up to 1 670 connectors per hour
108 [2 745] W x 54 [1 370] D x
60 [1 525] H; 750 lb [340 kg]
Depending on cable lengths, can apply
and test up to 2 000 connectors per hour
48 [1 220] W x 48 [1 220] D x
62 [1 575] H; 630 lb [286 kg]
Depending on cable lengths, can apply
and test up to 1 050 connectors per hour
68 [1 730] W x 58 [1 475] D x
72 [1 830] H; 1 300 lb [590 kg]
Operated and programmed by a
touchscreen
Operated and programmed by a
touchscreen
Operated and programmed by a
touchscreen or a keyboard
Programmable
Parameters for up to 130 cable assem-
blies can be retained in memory
Parameters for up to 150 cable assem-
blies can be retained in memory
Parameters for up to 1 000 cable assem-
blies can be retained in memory
Another menu displays production totals Another menu displays production totals
—
or a log of the machine events
or a log of the machine events
Testing
Automatically stops after each or three
consecutive assemblies are rejected, as
programmed by the operator
Automatically stops when either a con-
secutive number of assemblies or a
percentage of the batch run are rejected,
as programmed by the operator
Automatically stops each time a
malfunction is detected
Changeover
Requires an average of 25 minutes,
depending on assembly size
Requires an average of 15 minutes,
depending on assembly size
Requires an average of 20 minutes to
1 hour, depending on assembly size
and type
*Note: Machine may require accessories. Before ordering, contact TE at the numbers listed below.
Catalog 82012
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches
and millimeters unless
otherwise specified.
USA: [phone]
Canada: [phone]
Mexico/C. Am.: [phone]
Latin/S. Am.: [phone]
Germany: [phone]
71
UK: [phone]
France: [phone]
Netherlands: [phone]
China: [phone]