2-1437402-5 Datasheet, PDF (42/69 Pages) Tyco Electronics – Engineering Notes

BUCHANAN Terminal Blocks
Note: All part numbers
are RoHS Compliant.
0.4375” [11.1] Pitch, Series SSB7 (Continued)
Contact Spacing Options:
.4375 in (7/16") Spacing
Extra thick barriers provide higher
voltage rating. Up to 27 ckts. (25
circuits for end mounted blocks)
Base Options:
Closed Base
Catalog Letter
Code: C. For
terminal junction-
blocks requiring
top connections
only. Useful in
applications
requiring single point circuit
terminations or circuit completion via
top mounted, single- and two-sided
quick-connects. Replace double-row
barrier strips.
Flat Base
Catalog Letter
Code: F. Lends
itself most readily
to applications
where direct top-
to-bottom feed-
through is required with no special
requirement for circuit isolation on the
bottom side. The most common
example of this is printed circuit
board mounting.
Raised Base
Catalog Letter Code R. Standoffs
between each circuit raise block
.030" above mounting surface to
allow flux and solvents to drain
during soldering operations.
Available only with 02 and 04 bottom
terminals.
Turret Base
Catalog Letter Code: T. Combines
top-to-bottom
feed-through
with bottom-side
circuit isolation
for panels up to
.126" thick. Turret
bases are available with the following
terminals: solder tail, quick connect,
machine wrap, extended circuit
board terminal, and right-angle.
Mounting Options:
End Position
Mounting
Catalog Letter
Codes: E, F, G
or M. Supplied
without contacts in end sections to
allow installer to mount blocks with
screws in end section holes. Base of
block will support mounting screws
(Codes F & M). Also available with
mounting inserts installed in end
mounting holes to raise mounting
screw heads to the level of other top
hardware (Codes E & G).
Without End Barriers
Catalog Letter Codes: F, G & H.
Facilitates mounting-screw access
when end sections are used for
mounting.
Direct Mounting
Catalog Letter Codes: P & H. SSBs
may be solder-mounted using the
bottom terminals themselves, as in
the case of printed circuit board
applications.
Direct mounting is also possible with
turret base models using press-on
retaining clips (Catalog No. L97, Part
Number 1437661-7) on turrets.
Hardware Options
7C1xxx—Safety cover, see page 175
QC2x—.250 Quick connects,
see page 176
QC4x—.187 Quick connects,
see page 176
ST80—Single sided solder tabs,
see page 176
1776090-x—Extra long Quick
connects, see page 176
J7—Jumpers, see page 177
L91—Mounting insert, see page 178
L92—Angle bracket, see page 178
Terminal Style:
Solder Tail
Catalog Number
Code: 01. For
applications requiring
a wrapped solder
connection.
Printed Circuit Pin
Catalog Number
Code: 02.
Designed specifically
for mounting on .063"
thick circuit board.
Special, readily
solderable plating permits good fillet
development in automated soldering
processes.
Non-Feed-Through
Catalog Number
Code: 03.
With closed base
option only.
Extended Printed
Circuit Pin
Catalog Number
Code: 04.
Useful where extra
length is needed, as in
thicker printed circuit
boards or single-wrap
connections.
Quick Connect
Catalog Number Code:
05. .250 in. wide x
.032" thick blades
accept .250" female
quick connects.
2
Catalog 1308389
Revised 6-07
www.tycoelectronics.com
Dimensions are in millimeters
and inches unless otherwise
specified.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
LR25557 E63810
153
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 8706-080-208