HB15M0FZRE Datasheet, PDF (1/2 Pages) Tyco Electronics – Type HB Series

High Value / High Voltage Resistors
Key Features
I Up to 15kV Element
Voltage
• Unique specification
for the most deman-
ding applications
I High Ratio of Size
to Power
• The solution to your
PCB population
problems
I 1kW to 1GW
• ^{Coupled with 1%}
tolerance gives
ultimate design
flexibility
I Established Product
with Proven Reliability
I Low Inductance
• ^{For the fastest}
switching speeds
Applications
I High Voltage
I Voltage Divider
I Surge
I Filter
I Balancing
I Inrush Limiting
Type HB Series
TE Connectivity (TE) is a leading supplier of standard and custom designed high
value/high voltage resistors for high voltage, industrial, control, medical and
general-purpose use. The HB is a tough epoxy coated high voltage resistor, with axial or
radial leads, values up to 1G Ohm and an operational voltage to 20kV as standard and
30kV to order. The resistors are made from quality materials for optimum reliability and
stability. TE can test resistors to conform to relevant international, MIL or customer
specifications. TE is happy to advise on the use of resistors for high frequency
applications and to supply information for high voltage use.
Characteristics - Electrical
HBA
HB1
HB3
Power Dissipation - Power @ 20°C (W):
0.8
2.0
4.0
@ 70°C:
0.4
1.0
2.0
Ohmic Value - Min (Ohms):
1K
10K
10K
Max:
120M
1G
1G
Resistance Tolerance (%) (Tighter By Request):
1%, 2%, 5% 1%, 2%, 5% 1%, 2%, 5%
Maximum Working Voltage - DC or ACrms (Volts):
1kV
7.5kV
15kV
Insulation Resistance - Epoxy Coated, @500V dc (Ohms):
>10⁶MΩ
>10⁶MΩ
>10⁶MΩ
Load Stability - 1000hr’s @ 70°C (%):
±0.5%
±0.5%
±0.5%
Temp. Rapid Change - -55°C to 125°C for 5 cycles (ΔR):
±0.1%
±0.1%
±0.1%
Endurance - 1000 Hours @ 200°C (ΔR):
<=2%
<=2%
<=2%
Resistance to Soldering Heat - 350°C for 3.5seconds (ΔR):
0.05%
0.05%
0.05%
Temperature Coefficient (ppm/°C):
±100ppm/°C ±100ppm/°C ±100ppm/°C
(±20ppm/°C available to special order)
Voltage Coefficient:
Negligible up to 100K
Negligible up to 200K
Increasing to 0.02ppm/Volt at 800K
Increasing to
0.01ppm/Volt at 1M0
Increasing to 1.0ppm/Volt at 5M0
Increasing to
1.0ppm/Volt at 10M
Increasing to 2.0ppm/Volt at 50M
Increasing to
2.0ppm/Volt at 100M
Increasing to 8.0ppm/Volt at 1000M
Increasing to
8.0ppm/Volt at 1000M
Ambient Temperature Range (°C):
-55 to 125
-55 to 125
-55 to 125
Long Term Damp Heat (%):
0.25%
0.25%
0.25%
(Steady state 56 Days 95% RH at 40°C)
Noise (Quantech) Dependent
-20dB (0.1μ V/V) at lower values
on Resistor Type and Value:
+10dB (3.3μ V/V) at higher values
Encapsulation:
Epoxy coating (Optional)
Solvent Resistance:
Print will withstand the action of all
commonly used industrial solvents.
Lead Material:
Tinned copper wire
Lead Length:
Minimum 20mm
Lead Diameter:
Nominal 0.6 ± 0.05mm
1773310 CIS BI 06/2011
Dimensions are in millimeters
and inches unless otherwise
specified. Values in brackets
are standard equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
For email, phone or live chat, go to: te.com/help