DP52-0002 Datasheet, PDF (1/2 Pages) Tyco Electronics – Low Cost SMT Dual Band Diplexer

Low Cost SMT Dual Band Diplexer
DP52-0002
DP52-0002
Low Cost SMT Dual Band Diplexer
824 – 960 / 1850 – 1990 MHz (AMPS/PCS)
880 – 960 / 1700 – 1900 MHz (GSM/DCS)
Features
• Small Size and Low Profile
• Industry Standard SOIC-8 SMT Plastic Package
• Superior Repeatability
• Passbands 824 - 960 MHz and 1850 - 1990 MHz
• Passbands 880 - 960 MHz and 1700 - 1900 MHz
• Typical Passband Insertion Loss: 0.5 dB
• 2 Watt Power Handling
• Low Cost
Description
M/A-COM’s DP52-0002 is an IC-based monolithic diplexer in a
low cost SOIC-8 SMT plastic package. This diplexer is ideally
suited for applications where small size, low insertion loss, supe-
rior repeatability and low cost are required. Typical applications
include AMPS/PCS and GSM/DCS dual mode portable devices.
The DP52-0002 is fabricated using a passive-integrated circuit
process. The process features full-chip passivation for increased
performance and reliability.
SO-8
PIN 8
Orientation
mark
.1497-.1574
(3.80-4.00)
-B-
.2284-.2440
(5.80-6.20)
.010(0.25) M B M
PIN 1
.1890-.1968
(4.80-5.00)
-A-
.004 (0.10)
.050(1.27) BSC.
.0532-.0688
(1.35-1.75)
0°-8°
-C-
.0040-.0098
(0.10-0.25)
.013-.020 TYP.
(0.33-0.51)
.0099-0.0196
x 45° Chamfer
(0.25-0.50)
.016-.050
(0.40-1.27)
.0075-0.0098
(0.19-0.25)
.010(0.25) M C A M B S
8- Lead SOP outline dimensions
Narrow body .150
(All dimensions per JEDEC No. MS-012-AA, Issue C)
Dimensions in ( ) are in mm.
Unless Otherwise Noted: .xxx = ± 0.010 (.xx = ± 0.25)
.xx = ± 0.02 (.x = ±0.5)
Ordering Information
Part Number
Package
DP52-0002
DP52-0002-TR
SOIC-8-Lead Plastic Package
Forward Tape and Reel¹
1. If specific reel size is required, consult factory for part number
assignment.
824 - 960 / 1850 - 1990 MHz Typical Electrical Specifications¹, T_A= +25ºC
Parameters
Passband Insertion Loss
Stopband Isolation
Passband VSWR
Units
dB
dB
—
Min.
—
12
—
Typ.
0.5
18
1.4:1
1. All specifications apply with a 50-ohm source and load impedance.
880 - 960 / 1700 - 1900 MHz Typical Electrical Specifications¹, T_A= +25ºC
Parameters
Passband Insertion Loss
Stopband Isolation
Passband VSWR
Units
dB
dB
—
Min.
—
12
—
Typ.
0.5
18
1.5:1
1. All specifications apply with a 50-ohm source and load impedance.
Max.
0.8
—
1.7:1
Max.
0.9
—
1.8:1
M/A-COM Division of AMP Incorporated s North America: Tel. [phone], Fax [phone] s Asia/Pacific: Tel.[phone], Fax [phone] s
Europe: Tel. [phone], Fax[phone]
www.macom.com
AMP and Connecting at a Higher Level are trademarks.
Specifications subject to change without notice.
V2.00