CAP200 Datasheet, PDF (1/2 Pages) Tyco Electronics – CAP200 Series Contactor With 1 Form A (SPST-NO) Contacts Rated up to 500 Amps, 12-900VDC

CAP200 Series Contactor With 1 Form A (SPST-NO)
Contacts Rated up to 500 Amps, 12-900VDC
Product Facts
s Designed to be the smallest,
lightest weight, lowest cost
sealed contactor in the industry
with its current rating.
s Built-in coil economizer – only
1.7W hold power @ 12VDC and
it limits back EMF to 0V.
(models requiring extenal
economizer also available).
s Optional auxiliary contact for
easy monitoring of power
contact postion.
s Hermetically sealed –
intrinsically safe, operates in
explosive/harsh environments
with no oxidation or
contamination of coils or
contacts, including long periods
of non-operation.
s Versatile coil and power
connections.
s UL Recognized for the U.S. and
Canada (File E208033).
s CE marked for EC applications.
s AIAG QS9000 designed, built
and approved
For factory-direct application assistance, dial
800-253-4560, ext. 2053, or 805-220-2053.
Performance Data
Parameter
Units Value for CAP200 Series
Contact Arrangement, power contacts
1 Form A (SPST-NO)
Rated Operating Voltage
VDC 12 - 900
Continuous (Carry) Current, Typical
A 500 @ 85°C, 400 mcm conductors
Consult Factory for required conductors for higher currents
Make/Break Current at Various Voltages ^1/ A See next page
Break Current at 320VDC ^1/
A 2,000, 1 cycle ^3/
Contact Resistance, Typ. (@200A) mohms 0.2
Load Life
Cycles See next page
Mechanical Life
Cycles 1 million
Contact Arrangement, auxiliary contacts
1 Form A (SPST-NO)
Aux. Contact Current, Max.
Aux. Contact Current, Min.
A 2A @ 30VDC / 3A @ 125VAC
mA 100mA @ 8V
Aux. Contact Resistance, Max.
ohms 0.417@ 30VDC / .150 @ 125VAC
Dielectric Withstanding Voltage
Vrms 2,200 @ sea level
Insulation Resistance @ 500VDC megohms 100 ^2/
Shock, 11ms 1/2 sine, peak, operating G 20
Vibration, sine, 80-2000Hz., peak
G 20
Operating Temperature
°C -40 to +85
Weight, Nominal
lb.(kg) .95 (.43)
1/ _{Main power contacts}
2/ _{50 at end of life}
3/ _{Does not meet dielectric & IR after test, 1700 amp for unit with Aux. Contacts}
4/ _{Use with AMP LOUVERTAC 5-192013-9. Consult factory for threaded mount socket.}
© 2004 by Tyco Electronics Corporation. All Rights Reserved.
KILOVAC, AMP, LOUVERTAC and TYCO are trademarks.
Other products and company names mentioned herein may be trademarks of their
respective owners.
Coil Operating Voltage (valid over temperature range)
Voltage (will operate)
9-36VDC
32-95VDC 48-95VDC
Voltage (Max.)
36VDC
95VDC 95VDC
Pickup (close) Voltage Max.
9VDC
32VDC 48VDC
Hold Voltage (Min.)
7.5VDC
22VDC 34VDC
Dropout (open) Voltage (Min.)
6VDC
18VDC 27VDC
Inrush Current (Max.)
3.8A
1.3A
0.7A
Holding Current (Avg.)
0.13A@12V, 0.07A@24V 0.03A@48V 0.02A@72V
Inrush Time (Max.)
130ms
130ms 130ms
Part Numbering System
Typical Part Number
CAP200 A A A N A
Series:
CAP200 = 500 Amp, 12-900VDC Contactor
Contact Form:
A = Normally Open
H = Normally Open with Aux. Contacts
Coil Voltage:
A = 9-36VDC (1 = requires external coil economizer)
D = 32-95VDC (2 = requires external coil economizer)
J = 48-95VDC (3 = requires external coil economizer)
Coil Wire Length:
A = 15.3 in (390 mm)
B = 6.0 in (152 mm)
Coil Terminal Connector:
N = None
E = 9-pin subminiature “D” plug mounted on contactor housing
F = 9-pin subminiature “D” plug mounted on 15.3 in (390 mm) flying leads.
X = Special configuration (consult factory)
Mounting & Power Terminals:
A = Bottom Mount & Male 10mm x 8 Terminals
C = Plug-in Terminals ^4/
Catalog 1654770
Revised 6-04
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
1
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967