55PC1246 Datasheet, PDF (1/1 Pages) Tyco Electronics – This specification sheet forms a part of the latest issue of Raychem Specification 55PC.

TITLE
SPECIFICATION CONTROL DRAWING
Date
FOUR CONDUCTOR CABLE, SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT
This specification sheet forms a part of the latest issue of Raychem Specification 55PC.
11-22-06
55PC1246
Revision
A
COMPONENT WIRES - 55PC0216
SHIELD - NICKEL-COATED COPPER
JACKET - RADIATION-CROSSLINKED,
MODIFIED ETFE
PART NUMBER
1/
55PC1246-26-*
55PC1246-24-*
55PC1246-22-*
55PC1246-20-*
55PC1246-18-*
55PC1246-16-*
CONDUCTOR
SIZE
(AWG)
26
24
22
20
18
16
SHIELD
SIZE
(AWG)
38
38
38
38
38
38
CONSTRUCTION DETAILS
JACKET THICKNESS
(in.)
LOWER SPEC
LIMIT
.0060
.0060
.0060
.0065
.0065
.0065
TARGET
WALL
.0080
.0080
.0080
.0085
.0085
.0085
LOWER SPEC
LIMIT
.109
.119
.132
.150
.173
.188
DIAMETER
( in.)
TARGET
VALUE
.123
.135
.150
.173
.197
.217
UPPER SPEC
LIMIT
.137
.150
.168
.195
.221
.245
WEIGHT
( lbs/1000 ft. )
TARGET
VALUE
12.22
15.35
20.07
27.62
38.16
46.71
UPPER SPEC
LIMIT
12.84
15.96
20.74
28.50
39.24
47.95
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 200°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz
CROSSLINK VERIFICATION: 300 ± 3°C for 1 hour
JACKET COLOR: White preferred
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 50% (minimum)
Tensile Strength, 5000 lbf/in² (minimum)
JACKET FLAWS:
Spark Test, 1000 volts (rms)
Impulse Dielectric Test, 6.0 kV (peak)
SHIELD COVERAGE: 85% (minimum)
VOLTAGE WITHSTAND TEST (Post Environmental):
1000 volts (rms), 60 Hz, 1 minute
PART NUMBER:
The "*" in the part numbers above shall be replaced by color code
designators with a slash separating the component wire colors and a
dash separating the component wire colors from the jacket color.
1/ Example: AWG 22, red, yellow, green and blue component wires;
white jacket: 55PC1246-22-2/4/5/6-9
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL
Page 1 of 1
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
R Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: [phone]
Fax: [phone]
© 2006 Tyco Electronics Corporation. All rights reserved.