55FA0531 Datasheet, PDF (1/1 Pages) Tyco Electronics – This specification sheet forms a part of the latest issue of Raychem Specification 55F.

SPECIFICATION CONTROL DRAWING
TITLE
Date
THREE CONDUCTOR CABLE, UNSHIELDED, UNJACKETED, FILTER LINE - ELECTROLOSS
8-6-10
This specification sheet forms a part of the latest issue of Raychem Specification 55F.
COMPONENT WIRES - 55FA0511
55FA0531
Revision
B
PART NUMBER
1/
55FA0531-22-*
55FA0531-20-*
55FA0531-18-*
55FA0531-16-*
55FA0531-14-*
55FA0531-12-*
55FA0531-10-*
CABLE CONSTRUCTION DETAILS
CONDUCTOR
SIZE
(AWG)
OUTSIDE DIAMETER
(inches)
NOMINAL
MAXIMUM
22
.110
.117
20
.127
.134
18
.151
.158
16
.169
.177
14
.205
.214
12
.242
.251
10
.294
.305
MAXIMUM
WEIGHT
(lbs/1000 ft.)
12.2
17.7
26.6
34.3
49.3
73.4
113.
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 150°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
INSULATION FLAWS:
Spark Test, 3.0 kV (rms) at 60 Hz
5.7 kV (rms) at 3 kHz
Impulse Dielectric Test, 8.0 kV (peak)
VOLTAGE WITHSTAND (DIELECTRIC):
Conductor to conductor, 1500 volts (rms), 60 Hz
PART NUMBER:
The "*" in the part numbers above shall be replaced by color code designators; except that violet
shall be light violet and the designator shall be 7L; with a slash separating the component wire colors.
Colors shown do not necessarily reflect the sequence of manufacturing.
1/ Example: AWG 22, light violet, light violet with an orange stripe and light violet with a blue stripe
component wires: 55FA0531-22-7L/7L3/7L6
This product meets or exceeds all requirements of SAE AS85485/11 for 22-14 AWG, less identification.
Internal wire sizes 22-10 AWG meet or exceed all requirements of SAE AS85485/9, less identification.
All other AWG sizes meet or exceed all requirements of SAE AS85485, less identification.
NOTE: Nominal values are for information only.
Nominal values are not requirements.
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
Page 1 of 1
The TE logo, Tyco Electronics, Raychem and Electroloss are trademarks.
DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
Raychem Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: [phone]
Fax: [phone]
© 2010 Tyco Electronics Corporation. All rights reserved.