SW-110-PIN Datasheet, PDF (2/5 Pages) Tyco Electronics – GaAs SPDT Reflective Switch with TTL/CMOS Control Input, DC - 3.0 GHz

SW-110-PIN
GaAs SPDT Reflective Switch with TTL/CMOS Control Input,
DC-3.0 GHz
Electrical Specifications: T_A = 25°C^1,2,3
Rev. V6
Parameter
Reference
Insertion Loss
Isolation
VSWR
Trise, Tfall
Ton, Toff
Transients
Test Conditions
—
—
—
10% to 90%
1.3V Control to 90/10% RF
In-band (peak-peak)
Frequency
DC - 0.5 GHz
DC - 1.0 GHz
DC - 2.0 GHz
DC - 3.0 GHz
DC - 0.5 GHz
DC - 1.0 GHz
DC - 2.0 GHz
DC - 3.0 GHz
DC - 0.5 GHz
DC - 1.0 GHz
DC - 2.0 GHz
DC - 3.0 GHz
—
—
—
Units
dB
dB
dB
dB
dB
dB
dB
dB
Ratio
Ratio
Ratio
Ratio
nS
nS
mV
Min
—
—
—
—
40
35
24
18
—
—
—
—
—
—
—
Typ
—
—
—
—
—
—
—
—
—
—
—
—
12
35
30
Max
0.6
0.7
0.9
1.1
—
—
—
—
1.2:1
1.4:1
1.4:1
1.5:1
—
—
—
1 dB Compression
Input IP₃
Vcc
Vee
Icc
Iee
Vctl
Vctl
Input Leakage
Current (Low)
Input Leakage
Current (High)
Input Power, 0.1 dB, -5V Control
Input Power, 1.0 dB, -5V Control
Input Power, 0.1 dB, -8V Control
Input Power, 1.0 dB, -8V Control
For two-tone Input power up to +10
dBm
-5V Control
-8V Control
Vcc = 4.5 to 5.5V
Vctl = 0 to 0.8V, or VCC - 2.1V to
VCC
Vee = -5.0 to –8.0V
Logic 0 (TTL)
Logic 1 (TTL)
0 to 0.8V
2.0 to 5.0V
0.9 GHz
0.9 GHz
0.9 GHz
0.9 GHz
0.9 GHz
0.9 GHz
—
—
—
—
—
—
—
—
dBm
—
+32.5
—
dBm
—
+32.5
—
dBm
—
+32.5
—
dBm
—
+39.5
—
dBm
—
+61
—
dBm
—
+65
—
V
4.5
5.0
5.5
V
-8.0
—
-5.0
mA
—
—
1.0
mA
—
—
1.0
V
0.0
—
0.8
V
2.0
—
5.0
µA
—
—
1.0
µA
—
—
1.0
1. All specifications apply when operated with bias voltages of +5V for Vcc and –5.0V to –8.0V for Vee, and 50 Ohm impedance at all RF
ports unless otherwise specified.
2. For this switch to meet the guaranteed specifications, it is necessary to have a DC return on either RF1 or RF2. The DC return can be
either a 10k Ohm resistor, or an RF choke.
3. High Power (greater than 1W) handling specifications apply to cold switching only. For input powers under 1W, hot switching can be
used.
2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: [phone] • Europe Tel: [phone]
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
• India Tel: [phone]
• China Tel: [phone]
Visit www.macomtech.com for additional data sheets and product information.
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. _{M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make}
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.