MADR-008888-000100_15 Datasheet, PDF (2/5 Pages) M/A-COM Technology Solutions, Inc. – PIN Diode Driver for Series / Series High Power Switch

MADR-008888-000100
PIN Diode Driver for Series / Series High Power Switch
Rev. 5
Electrical Specifications: T_A = +25C, +VCC = +5.0 V, VDD = +28 V
Parameter
DC Output Current
RX Current ⁴
TX Current ⁴
Test Conditions
Assumes 1V Drop on PIN Diode
Assumes 1V Drop on PIN Diode
Unit
mA
mA
Min
—
—
Back Bias Voltage on
TX Diode
RX Diode
RX ON
TX ON
V
—
V
—
Switching Speed: ANT-TX⁵
Ton
Toff
Trise
Tfall
50% CTL to 90% Voltage
50% CTL to 10% Voltage
10% - 90%
90% - 10%
µs
—
µs
—
ns
—
ns
—
Typ
22 or 35
22 or 35
27
27
0.9
1.5
250
300
Max
50
50
—
—
2.0⁶
2.0⁶
—
—
Switching Speed: ANT-RX⁵
Ton
Toff
Trise
Tfall
50% CTL to 90% Voltage
50% CTL to 10% Voltage
10% - 90%
90% - 10%
µs
—
1.5
2.0⁶
µs
—
0.9
2.0⁶
ns
—
200
—
ns
—
250
—
PRF
Quiescent Supply Currents
Logic Levels
50% duty cycle
KHz
DC
—
50
VCC (+5V)
VDD (+28V)
mA
—
—
0.1
mA
—
—
5.0
Logic “0” @ 20 µA sink current
V
0.0
0.0
1.5
Logic “1” @ 0.5 mA source current
V
3.5
5.0
5.0
Supply Currents⁴
ICC
IDD
R1 = 80 Ω
R1 = 110 Ω
R1 = 180 Ω
R1 = N/A
mA
—
51
—
mA
—
36
—
mA
—
23
—
mA
—
2.5
—
4. Currents are user selectable. Reference “Driver and SPDT Schematic” for suggested values. R1 should be ≥ 80 ohms for VCC= 5.0V.
R1 should be ≥ 65 ohms for VCC = 3.3V.
5. Switch parameters were measured when driving the MASW-000823-12770T switch.
6. Maximums are for load currents up to 25mA
Recommended Operating Conditions
Parameter
VCC
VDD
Test Conditions
Nominal VCC = 3.3 V
Nominal VCC = 5.0 V
Input Voltage
Unit
V
V
V
Min
3.0
4.5
27.0
Typ
3.3
5.0
28.0
Max
3.6
5.5
29.0
C1 (Low Level Input Voltage)
C1 (High Level Input Voltage)
VCC = 3.0 V to 3.6V
VCC = 4.5 V to 5.5 V
VCC = 3.0 V to 3.6V
VCC = 4.5 V to 5.5 V
V
0.0
0.0
0.8
V
0.0
0.0
0.3 x VCC
V
2
VCC
V
0.7 x VCC
VCC
VCC
VCC
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Silicon Circuits are sensitive to electrostatic
discharge (ESD) and can be damaged by static
electricity. Proper ESD control techniques should
be used when handling these devices.
2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: [phone] • Europe Tel: [phone]
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
• India Tel: [phone]
• China Tel: [phone]
Visit www.macomtech.com for additional data sheets and product information.
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. _{M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make}
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.