MAAD-007077 Datasheet, PDF (2/6 Pages) M/A-COM Technology Solutions, Inc. – Contains Internal DC to DC Converter

MAAD-007077
Digital Attenuator
15 dB, 4-Bit, TTL Driver, DC-4.0 GHz
Rev. V5
Electrical Specifications: T_A = 25°C, Z₀ = 50
Parameter
Test Conditions
Frequency
Insertion Loss
—
DC-2.5 GHz
DC-4.0 GHz
Attenuation
Accuracy
Individual Bits or
Combination of Bits
DC-2.5 GHz
DC-4.0 GHz
VSWR
Full Attenuation Range
DC-2.5 GHz
DC-4.0 GHz
Switching Speed
50% Cntl to 90%/10% RF
—
10% to 90% or 90% to 10%
—
1 dB Compression
—
50 MHz
0.5-4.0 GHz
Input IP₃
Two-tone Inputs up to +5 dBm
50 MHz
0.5-4.0 GHz
Vcc
—
—
V_IL
LOW-level input voltage
—
V_IH
HIGH-level input voltage
—
lin (Input Leakage Current)
Vin = V_CC or GND
—
Icc⁴
Vcc min to max, Logic “0” or “1”
—
Turn-on Current⁵
For guaranteed start-up
—
ΔIcc
V_CC = Max, Vcntrl = V_CC - 2.1 V
—
(Additional Supply Current
Per TTL Input Pin)
Switching Noise
Generated from
DC-DC Converter with
recommended capacitors
3.5 MHz
Thermal Resistance θjc
—
—
Units
dB
dB
dB
dB
Ratio
Ratio
ns
ns
dBm
dBm
dBm
dBm
V
V
V
uA
mA
mA
mA
Min
—
—
—
—
—
—
—
—
—
—
—
—
4.75
0.0
2.0
-1.0
—
—
—
dBm
—
°C/W
—
Typ
2.0
2.5
—
—
1.5:1
1.8:1
25
4
+21
+27
+35
+48
5.0
—
—
—
6
—
—
Max
2.5
3.0
±(0.3+4% of atten setting)
±(0.3+6% of atten setting)
1.8:1
2.0:1
—
—
—
—
—
—
5.25
0.8
5.0
1.0
10
125
1.5
-93
—
15
—
4. During turn-on, the device requires an initial start up current (Icc)
specified as “Turn-on Current”. Once operational, Icc will drop to the
specified levels.
5. The DC-DC converter is guaranteed to start in 100 µs as long as the
power supplies have the maximum turn-on current available for start-
up.
Absolute Maximum Ratings ^6,7
Recommended PCB Configuration⁹
Parameter
Max. Input Power
0.05 GHz
0.5 - 4.0 GHz
V_CC
Vin⁸
Operating Temperature
Absolute Maximum
+27 dBm
+34 dBm
-0.5V ≤ V_CC ≤ +6.0V
-0.5V ≤ Vin ≤ V_CC + 0.5V
-40ºC to +85ºC
Storage Temperature
-65ºC to +125ºC
6. Exceeding any one or combination of these limits may cause
permanent damage to this device.
7. M/A-COM does not recommend sustained operation near
these survivability limits.
8. Standard CMOS TTL interface, latch-up will occur if logic sig-
2
nal is applied prior to power supply.
9. Application Note S2083 is available on line at www.macom.com
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support