AT20-0107_15 Datasheet, PDF (2/4 Pages) M/A-COM Technology Solutions, Inc. – Digital Attenuator

AT20-0107
Digital Attenuator
31.5 dB, 6-Bit, TTL Driver, DC-2.0 GHz
Electrical Specifications: T_A = +25°C²
Rev. V7
Parameter
Insertion Loss
Attenuation Accuracy^1,3,4
VSWR
Trise, Tfall
Ton, Toff
Transients
1 dB Compression ⁵
Input IP₃ ⁵
Input IP₂ ⁵
Vcc
-Vee
Icc
-Iee
Test Conditions
—
Any Bit or Combination of
Bits
Full Range
10% to 90%
50% Control to 90%/10%
RF
In-band (peak to peak)
Input Power
Input Power
Two Tone Inputs up to
+5 dBm
Two Tone Inputs up to
+5 dBm
—
—
Vcc = 4.5 to 5.5V
-Vee = -5.0 to -8.0V
Frequency
DC - 2.0 GHz
DC - 2.0 GHz
DC - 2.0 GHz
—
—
—
50 MHz
0.5 - 2.0 GHz
50 MHz
0.5 - 2.0 GHz
50 MHz
0.5 - 2.0 GHz
—
—
—
—
Units
dB
dB
Ratio
ns
ns
mV
dBm
dBm
dBm
dBm
dBm
dBm
V
V
mA
mA
Min
—
—
—
—
—
—
—
—
—
—
—
—
4.5
-8.0
—
—
Typ
3.2
—
—
50
150
50
Max
3.8
+(.3 +7% of atten.)
-(.2 +1% of atten.)
1.8:1
—
—
—
+21
—
+29
—
+35
—
+48
—
+45
—
+79
—
5.0
5.5
—
-5.0
—
6.0
—
1.0
1. Above reference insertion loss.
2. All specifications apply when operated with bias voltages of +5V for V_CC and –5.0 V to –8.0 V for V_EE and 50Ω impedance at all ports
unless otherwise stated.
3. This attenuator is guaranteed monotonic.
4. For the attenuator to meet the guaranteed specifications, it is necessary to have a DC return on either RF1 or RF2. The DC return can be
either a 10KΩ resistor, or an RF choke.
5. V_EE = -5 V for the typical numbers given.
Absolute Maximum Ratings ^6,7
Recommended PCB Configuration
Parameter
Absolute Maximum
Max. Input Power
0.05 GHz
0.5 - 2.0 GHz
+27 dBm
+34 dBm
V_CC
V_EE
V_CC - V_EE
Vin⁸
Operating Temperature
-0.5V ≤ V_CC ≤ +7.0V
-8.5V ≤ V_EE ≤ +0.5V
-0.5V ≤ V_CC - V_EE ≤ 14.5V
-0.5V ≤ Vin ≤ V_CC + 0.5V
-40°C to +125°C
Storage Temperature
-65°C to +150°C
6. Exceeding any one or combination of these limits may cause
permanent damage to this device.
7. M/A-COM does not recommend sustained operation near
these survivability limits.
8. Standard CMOS TTL interface, latch-up will occur if logic
signal is applied prior to power supply.
2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: [phone] • Europe Tel: [phone]
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
• India Tel: [phone]
• China Tel: [phone]
Visit www.macomtech.com for additional data sheets and product information.
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. _{M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make}
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.