AR15W Datasheet, PDF (1/2 Pages) Lumins Inc. – Wall mount

L UMINIS
Hinged frame
1
2
3
White translucent
conical housing
4
5
6
7
Wall mount
Specification
ARGON
AR15W . AR15WL
All exposed cast aluminum components are made of non corrosive
pure aluminum copper free (Aluminum is less than .1% copper
content.#356 alloy.)
Finish: All polyester powder baked coatings preceded with
a 5 baths preparation process. Meets military grade
MIL-C781706 with a 2000 hours salt spray test.
- Pulse rated medium base porcelain socket.
- 75W/600V thermoplastic compact fluorescent socket.
- One-piece molded silicone gasket with memory retention.
- High power factor CWA ballast. Or 98% P.F.electronic smart
ballast with end of life detection for compact fluorescent.
- All stainless steel hardware.
- All Moving and removable parts are sealed with a
memory retention silicone gasket.
1 - 11 ga. galvanized pressure mounting plate.
2 - Cast aluminum isolated ballast compartment.
3 - Cone shaped white translucent conical housing
4 - Cast aluminum sealed hinged glass lens frame, with perimeter
memory retention embedded silicone gasket .
5 - Stainless steel recessed captive hexagonal cap screws.
6 - Tempered clear glass lens.
7 - Semi-specular partial down light reflector.
7 1/2”
For pole mounting, please refer to page 22 _AR15W:
AR15WL:
11 1/2”
13 1/2”
13 1/2”
ASH:
Regressed clear tempered glass lens.
White translucent acrylic frosted conical dropped lens.
Down light only.
Low brightness full cut-off 20”ø aluminum shade.
Compatible with AR15W-AR15WL
17 1/2”
19 1/2”
AR15WL Argon with conical lens
ASH: Optional
20”ø shade.
Adaptable to
AR15W &
AR15WL
3 1/2”
Photometry
5 1/8”
Separate updated technical
specification sheets with related
models and light sources with
I.E.S formatted photometry are
available on
90 www.luminis.com.
AR15W Argon with conical lens
60
Certification
UL. Wet Location.
Model#
AR15W
AR15WL
Mounting & E.P.A.
Max.weight: 21 lbs. EPA: 0.65
Installation: Mounts over a standard 4” octagonal
electrical box with 3 1/2” c/c mounting holes.
(by others ) additional separate mounting
holes are provided with wall plate.
Light source selection
Voltage
MH (ED17)
M50
M70
CF (Gx24q)
Single lamp
F157
F170
120 V Standard factory
prewired
(If no voltage is specified)
For other voltages, please
specify with catalog number.
H.I.D.
HPS (ED17)
H50
H70
CF (Gx24q)
Two lamp
F226
F232
F242
(Lamps by others)
208 V
240 V
277 V
347 V
Note: 50W.HPS
is available with
120/277V only.
COMP. FLUO.
Smart ballast 120/277
347 V (To specify)
30
Finish
(Refer to color chart)
Standard selection
WHT:Snow white
BKT: Jet black
BZT: Bronze
GRT: Titanium gray
DGT: Gun metal
CHT: Champagne
MST: Matte silver
GNT: Forest green
Optional colors
CS: Custom color
RAL: RAL# color
For options details and
specifications, please refer
to pages 22 - 41
Options
Accessories
CP:
Pole mounting adaptor.
see page 22
FS:
PH1:
PH2:
EM42S:
Electrical
Fuse
120/277V photo cell
347V photo cell
1 lamp (26/32/42W)
EM battery.
Note: EM optional battery test
switch and pilot lamp are installed
remotely. (See page 72) Available
for wall mounted luminaires only
luminaires may be altered for design improvements or discontinued without prior notice.
LUMINIS [ USA ] - 3555 NW 53rd Court, Fort Lauderdale, FL.33309 Tel: [phone] Fax: 954 . 717.4157
LUMINIS [ Canada ] - 87 C Brunswick D.D.O. Q.C. Canada H9B 2J5 Toll free: 888 .401 .6999
Page 21
Web: www.luminis.com
Sept.2006 Rev: Feb.2007