AR12W Datasheet, PDF (1/2 Pages) Lumins Inc. – Wall mount

L U MINIS
Wall mount
ARGON
AR12W . AR12W-UP . AR12WL
1
Specification
2
All exposed cast aluminum components are made of non corrosive
pure aluminum copper free (Aluminum is less than .1% copper
content.#356 alloy.)
Finish: All polyester powder baked coatings preceded with
a 5 baths preparation process. Meets military grade
MIL-C781706 with a 2000 hours salt spray test.
3
- Pulse rated medium base porcelain socket.
- 75W/600V thermoplastic compact fluorescent socket.
4
- One-piece molded silicone gasket with memory retention.
- High power factor CWA ballast. Or 98% P.F.electronic smart
ballast with end of life detection for compact fluorescent.
- All stainless steel hardware.
- All Moving and removable parts are sealed with a
5
memory retention silicone gasket.
Hinged frame
1 - 11 ga. galvanized pressure mounting plate.
2 - Cast aluminum isolated ballast compartment.
3 - Cone shaped heavy duty aluminum housing.
6
4 - Standard semi-specular type V distribution reflector.
5 - Cast aluminum sealed hinged glass lens frame, with perimeter
7
memory retention embedded silicone gasket .
6 - Stainless steel recessed captive hexagonal cap screws.
7 - Tempered clear glass lens.
7 1/2”
For pole mounting, please refer to page 22 ^AR12W:
AR12WL:
11 1/2”
13 1/2”
13 1/2”
AR12W-UP:
ASH:
5 1/8”
Regressed clear tempered glass lens.
White translucent acrylic frosted conical dropped lens.
Down light only.
(Up light model with additional flush mount protection
clear lens)
Low brightness full cut-off 20”ø aluminum shade.
Compatible with AR12W-AR12WL
17 1/2”
19 1/2”
AR12WL Argon with conical lens
21”
ASH: Optional
20”ø shade.
Adaptable to
AR12W &
AR12WL
3 1/2”
AR12W Argon with conical lens
AR12W-UP
Max: 100W
Certification
UL. Wet Location.
Mounting & E.P.A.
Max.weight: 22 lbs. EPA: 0.65
Installation: Mounts over a standard 4” octagonal
electrical box with 3 1/2” c/c mounting holes.
(by others ) additional separate mounting
holes are provided with wall plate.
Photometry
Separate updated technical
specification sheets with related
models and light sources with
I.E.S formatted photometry are
available on
90 www.luminis.com.
60
30
For options details and
specifications, please refer
to pages 22 - 41
Model#
Light source selection
Voltage
Finish
Options
AR12W
*AR12WL
*AR12W-UP
MH (ED17)
M70
M100
M150*
M175
CF (Gx24q)
Single lamp
F157
F170
HPS (ED17) CF (Gx24q)
H70
Two lamp
H100
H150
F226
F232
F242
* AR12WL: Max. 150W
AR12W-UP: Max.100W
(Lamps by others)
120 V Standard factory
prewired
(If no voltage is specified)
For other voltages, please
specify with catalog number.
H.I.D.
208 V
240 V
277 V
347 V
Note: 50W.HPS
is available with
120/277V only.
COMP. FLUO.
Smart ballast 120/277
347 V (To specify)
(Refer to color chart)
Standard selection
WHT:Snow white
BKT: Jet black
BZT: Bronze
GRT: Titanium gray
DGT: Gun metal
CHT: Champagne
MST: Matte silver
GNT: Forest green
Optional colors
CS: Custom color
RAL: RAL# color
luminaires may be altered for design improvements or discontinued without prior notice.
Accessories
ASH:
CP:
RA3:
RA4:
20” dia. alum. shade.
Pole mounting adaptor.
See page 22
Type III semi specular
reflector.
(Single lamps only.)
Forward Throw type
IV distribution
Electrical
FS:
PH1:
PH2:
EM42S:
Fuse
120/277V photo cell
347V photo cell
1 lamp (26/32/42W)
EM battery.
Note: EM optional battery test
switch and pilot lamp are installed
remotely. (See page 72) Available
for wall mounted luminaires only
LUMINIS [ USA ] - 3555 NW 53rd Court, Fort Lauderdale, FL.33309 Tel: [phone] Fax: 954 . 717.4157
LUMINIS [ Canada ] - 87 C Brunswick D.D.O. Q.C. Canada H9B 2J5 Toll free: 888 .401 .6999
Web: www.luminis.com
Sept.2006 Rev: Feb.2007
Page 20