AR10W Datasheet, PDF (1/2 Pages) Lumins Inc. – Wall mount

L U MINIS
Hinged frame
Wall mount
ARGON
1
AR10W . AR10W-UP . AR10WL
2
Specification
All exposed cast aluminum components are made of non corrosive
pure aluminum copper free (Aluminum is less than .1% copper
content.#356 alloy.)
Finish: All polyester powder baked coatings preceded with
3
a 5 baths preparation process. Meets military grade
MIL-C781706 with a 2000 hours salt spray test.
4
- Pulse rated medium base porcelain socket.
5
- 75W/600V thermoplastic compact fluorescent socket.
- One-piece molded silicone gasket with memory retention.
6
- High power factor CWA ballast. Or 98% P.F.electronic smart
ballast with end of life detection for compact fluorescent.
7
- All stainless steel hardware.
- All Moving and removable parts are sealed with a
memory retention silicone gasket.
8
9
For pole mounting, please refer to page 22
1 - 11 ga. galvanized pressure mounting plate.
2 - Cast aluminum isolated ballast compartment.
3 - Solid aluminum top cone
4 - Tempered clear glass for reflected light glow.
5 - Standard semi-specular type V distribution reflector.
6 - Cone shaped heavy duty aluminum housing.
7 - Cast aluminum sealed hinged glass lens frame, with perimeter
memory retention embedded silicone gasket .
8 - Stainless steel recessed captive hexagonal cap screws.
9 - Tempered clear glass lens.
7 1/2”
11 1/2”
13 1/2”
13 1/2”
17 1/2”
19 1/2”
AR10WL Argon with conical lens
21”
ASH: Optional
20”ø shade.
Adaptable to
AR10W &
AR10WL
AR10W-UP
Max: 100W
5 1/8”
AR10W Argon with flat lens
Certification
Mounting & E.P.A.
3 1/2”
AR10W:
AR10WL:
AR10W-UP:
ASH:
Regressed clear tempered glass lens.
White translucent acrylic frosted conical dropped lens.
Down light only.
(Up light model with additional flush mount protection
clear lens)
Low brightness full cut-off 20”ø aluminum shade.
Compatible with AR10W-AR10WL
Photometry
Separate updated technical
specification sheets with related
models and light sources with
I.E.S formatted photometry are
available on
90 www.luminis.com.
UL. Wet Location.
Max.weight: 22 lbs. EPA: 0.65
Installation: Mounts over a standard 4” octagonal
electrical box with 3 1/2” c/c mounting holes.
(by others ) additional separate mounting
holes are provided with wall plate.
60
30
For options details and
specifications, please refer
to pages 22 - 41
Model#
Light source selection
Voltage
Finish
Options
AR10W
*AR10WL
*AR10W-UP
MH (ED17)
M70
M100
M150
M175
CF (Gx24q)
Single lamp
F157
F170
HPS (ED17) CF (Gx24q)
H70
H100
H150
Two lamp
F226
F232
F242
* AR10WL: Max. 150W
AR10W-UP: Max.100W
(Lamps by others)
120 V Standard factory
prewired
(If no voltage is specified)
For other voltages, please
specify with catalog number.
(Refer to color chart)
Standard selection
WHT:Snow white
BKT: Jet black
H.I.D.
208 V
240 V
277 V
347 V
Note: 50W.HPS
is available with
120/277V only.
BZT: Bronze
GRT: Titanium gray
DGT: Gun metal
CHT: Champagne
MST: Matte silver
GNT: Forest green
Optional colors
COMP. FLUO.
Smart ballast 120/277
CS: Custom color
RAL: RAL# color
347 V (To specify)
luminaires may be altered for design improvements or discontinued without prior notice.
Accessories
ASH:
CP:
RA3:
RA4:
20” dia. alum. shade.
Pole mounting adaptor.
See page 22
Type III semi specular
reflector.
(Single lamps only.)
Forward Throw type
IV distribution
Electrical
FS:
PH1:
PH2:
EM42S:
Fuse
120/277V photo cell
347V photo cell
1 lamp (26/32/42W)
EM battery.
Note: EM optional battery test
switch and pilot lamp are installed
remotely. (See page 72) Available
for wall mounted luminaires only
LUMINIS [ USA ] - 3555 NW 53rd Court, Fort Lauderdale, FL.33309 Tel: [phone] Fax: 954 . 717.4157
LUMINIS [ Canada ] - 87 C Brunswick D.D.O. Q.C. Canada H9B 2J5 Toll free: 888 .401 .6999
Web: www.luminis.com
Sept.2006 Rev: Feb.2007
Page 19