5000 Datasheet, PDF (2/2 Pages) M.S. Kennedy Corporation – DUAL POSITIVE/NEGATIVE, 3 AMP, LOW DROPOUT FIXED VOLTAGE REGULATORS

Tgard™ 5000 Series
Thermally Conductive Insulators
PROPERTIES
ELECTRICAL PROPERTIES
Dielectric withstand voltage
50mm probe for 30 sec
Dielectric breakdown voltage
50mm probe
Volume resistivity
Dielectric constant @1Mhz
MECHANICAL PROPERTIES
Thickness
Hardness
Tensile strength
Elongation along width or length
Operating temperature range
Color
UL flammability rating
TEST METHOD METRIC VALUES
ASTM D149
ASTM D149
ASTN D257
ASTN D257
4,500 volts DC
Avg >6,000
volts AC
10¹² ohm-cm
3.4
ASTM D2240
ASTM D412
ASTM D412
UL 94
0.127 mm
75 Shore A
33.1 Mpa
45%
-60º to 180ºC
Tan
V-0
IMPERIAL VALUES
4,500 volts DC
Avg >6,000
volts AC
10¹² ohm-in
3.4
5 mils
75 Shore A
4.8 Kpsi
45%
-76º to 356ºF
Tan
V-0
PRESSURE
UNITS
10 25 50 100 200 400
(69) (172) (345) (689) (1379) (2758)
TOTAL THERMAL RESISTANCE
Modified ASTM D5470
ºC-in²/watt 0.62 0.51 0.40 0.27 0.25 0.23
Modified ASTM D5470
ºC-cm²/watt 4.0 3.29 2.58 2.06 1.61 1.48
T0-220
ºC/watt 1.31 1.00 0.82 0.65 0.58 0.54
Configurations available:
Standard options:
Standard die cut parts:
• Sheet form, roll form and die-cut parts
• Single-side, pressure-sensitive adhesive on request
• Without adhesive (A0): 12 x 18" sheets, 12" x 65M,
12" x 30M roll or custom configuration
• With adhesive (A1): 11.75 x 18" sheets, 11.75" x 30M roll
or custom configuration
Standard part sizes for TO-220, TO-247, TO-3P, TO-3PL and TO-264
Custom die cut parts:
Custom configurations available with standard tolerance of 0.5mm
(0.020”). Ability to handle drawings in multiple file formats. (.DXF
and .DWG preferred)
Data for design engineer guidance only. Observed performance varies in application.
Engineers are reminded to test the material in application.
THR-DS-Tgard-5000_032515
Any information furnished by Laird and its agents is believed to be accurate and reliable. All specifications are subject to change without notice. Responsibility for the use and
application of Laird materials rests with the end user, since Laird and its agents cannot be aware of all potential uses. Laird makes no warranties as to the fitness, merchantability
or suitability of any Laird materials or products for any specific or general uses. Laird, Laird Technologies, Inc or any of its affiliates or agents shall not be liable for incidental or
consequential damages of any kind. All Laird products are sold pursuant to the Laird Technologies’ Terms and Conditions of sale in effect from time to time, a copy of which will
be furnished upon request. © Copyright 2015 Laird Technologies, Inc. All Rights Reserved. Laird, Laird Technologies, the Laird Technologies Logo, and other marks are trademarks
or registered trademarks of Laird Technologies, Inc. or an affiliate company thereof. Other product or service names may be the property of third parties. Nothing herein
provides a license under any Laird or any third party intellectual property rights. Document A 15984-00 03/2015