HCR8065M3PBL-001 Datasheet, PDF (1/1 Pages) Laird Tech Smart Technology – ASSEMBLYANDINSTALLATIONINSTRUCTIONS

HCR8065M3PBL-001
HCR8065M3PWL-001
806-960MHz &1710-2200MHz HCR-M-3
ASSEMBLY AND INSTALLATION INSTRUCTIONS
SPECIFICATIONS
Model Number
Frequency
Gain (Typical)
Gain (Max)
VSWR
Max Input Power
Radiation Pattern
Polarization
Product Label With Laird Logo
Nominal Impedance
Antenna Dimension
Weight
Antenna Color
Wind Survival
Mounting
Operating Temperature
Storage Temperature
Ingression Protection
RoHS Compliance
HCR8065M3PBL-001
HCR8065M3PWL-001
806-960MHz
1710-2200MHz
2.1dBi
2.2dBi
2.6dBi
3.2dBi
< 2:1
10W
Omnidirectional
Vertical
Yes
50 Ohm
83.8(H)X36.5(Dia.)mm (Excludes Gasket Height)
192.5g
Black/White
282 km/h
P-Mount
-30ºC +70ºC
-40ºC +85ºC
IP67
YES
Antenna perspective view mounting
Warranty and Liability
Laird warrants to the original purchaser that antenna products will remain free from defects in
materials and workmanship for period of (5) years from the purchase date. If any such defect is
discovered within the warranty period, Laird will at its sole option, repair or replace the Product
free of charge upon its return to the factory. This warranty applies only if the Product is used in a
normal fashion, and is void if the Product is abused, disassembled, tampered with, used
unreasonably, or fails as a result of normal wear. Furthermore, this warranty applies only to
defects, which occur where the proper Product is selected as recommended by Laird and is used
in the fashion recommended by Laird for the defective Product. THIS WARRANTY IS IN LIEU OF
ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND IS LIMITED TO A PERIOD OF (5) YEARS
FROM THE DATE OF ORIGINAL PURCHASE. LAIRD IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND. ANY WARRANTY EXTENDED HEREIN SHALL BE LIMITED
TO THE PRICE PAID TO LAIRD FOR THE DEFECTIVE PRODUCT. WHERE STATE OR LOCAL LAW
GOVERNS THE PERIOD OF WARRANTY, SUCH PERIOD SHALL CONTROL.
Americas: +1.847 839.6907
[e-mail]
Europe: +44.1628.858941
[e-mail]
Asia; +1.65.6.243.8022
[e-mail]
www.lairdtech.com
Please read all instructions carefully before attempting
to install and use this product.
SAFETY
The HCR8065M3PBL-001, HCR8065M3PBL-001, and all
associated equipment should be installed in accordance with
applicable local and national electrical code guidelines to
ensure safe operation.
MOUNTING
1. Check your antenna to be certain the antenna resonant
frequency range and your radio are compatible.
2. Plan the mounting location on the ground plane. Be
certain to choose a flat area on the vehicle with a metal
thickness of 0.20” to 0.40”
3. Drill a 5/8” diameter hole and remove a 0.020” diameter
ring of paint from the around the hole to enable a firm
ground connection.
4. Insert the antenna threaded shaft through the hole in the
metal surface.
5. Insert the lock washer and thread the locking nut onto
the antenna shaft and be certain that the o-ring is in the
groove of antenna bush before tightening.
6. Tighten to 5-6 Nm of torque.
7. A light application of silicone grease to the o-ring will
prevent the o-ring from binding.
8. When finished, inspect for a proper bottom O-ring seal.
This will prevent water leaking into the mount and
perhaps into the machine/vehicle.
PRECAUTION
The antenna should be mounted on the desired location
before FUNCTIONING. This is to ensure that not damage
antenna during the mounting of the antenna.
IAS_165-00146-004_AA_081914