HCR8065M3NBL-001 Datasheet, PDF (1/1 Pages) Laird Tech Smart Technology – ASSEMBLYANDINSTALLATIONINSTRUCTIONS

SPECIFICATIONS
Model Number
Frequency
Gain (Typical)
Gain (Max)
VSWR
Max Input Power
Radiation Pattern
Polarization
Product Label With Laird Logo
Nominal Impedance
Antenna Dimension
Weight
Antenna Color
Wind Survival
Operating Temperature
Storage Temperature
Ingression Protection
RoHS Compliance
HCR8065M3NBL-001
HCR8065M3NWL-001
806-960MHz
1710-2200MHz
2.1dBi
2.2dBi
2.6dBi
3.2dBi
< 2:1
10W
Omnidirectional
Vertical
Yes
50 Ohm
83.8(H)X36.5(Dia.)mm (Excludes Gasket Height)
106g
Black/White
282 km/h
-30ºC +70ºC
-40ºC +85ºC
IP67
YES
Antenna perspective view mounting to NMO
Warranty and Liability
Laird warrants to the original purchaser that antenna products will remain free from defects in
materials and workmanship for period of (5) years from the purchase date. If any such defect is
discovered within the warranty period, Laird will at its sole option, repair or replace the Product
free of charge upon its return to the factory. This warranty applies only if the Product is used in a
normal fashion, and is void if the Product is abused, disassembled, tampered with, used
unreasonably, or fails as a result of normal wear. Furthermore, this warranty applies only to
defects, which occur where the proper Product is selected as recommended by Laird and is used
in the fashion recommended by Laird for the defective Product. THIS WARRANTY IS IN LIEU OF
ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND IS LIMITED TO A PERIOD OF (5) YEARS
FROM THE DATE OF ORIGINAL PURCHASE. LAIRD IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND. ANY WARRANTY EXTENDED HEREIN SHALL BE LIMITED
TO THE PRICE PAID TO LAIRD FOR THE DEFECTIVE PRODUCT. WHERE STATE OR LOCAL LAW
GOVERNS THE PERIOD OF WARRANTY, SUCH PERIOD SHALL CONTROL.
Americas: +1.847 839.6907
[e-mail]
Europe: +44.1628.858941
[e-mail]
Asia; +1.65.6.243.8022
[e-mail]
www.lairdtech.com
HCR8065M3NBL-001
HCR8065M3NWL-001
806-960MHz &1710-2200MHz HCR-M-3
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Please read all instructions carefully before
attempting to install and use this product.
SAFETY
The HCR8065M3NBL-001, HCR8065M3NWL-001 and all
associated equipment should be installed in accordance with
all applicable local and national electrical code guidelines to
ensure safe operation.
MOUNTING
The industry standard NMO mounting socket mates with all
Laird Technologies’ magnetic, trunk lid, and hole mounts.
Order Motorola style mount separately.
For ground plane or metal surface antennas:
1. Check your antenna to be certain the antenna
resonant frequency range and your radio are
compatible.
2. Prepare an NMO style mount on a metal surface. It is
recommended to mount at or nearest the center of
the surface away from other objects.
3. Install the HCR-M-3 antenna by tightening it onto a
threaded NMO style-mounting socket. A fair amount of
torque is needed to fully tighten the antenna until a
seal is obtained between the bottom O-ring and
vehicle surface. To assist tightening the antenna to the
mount, apply two small pieces of protective heat shrink
tubing to the jaws of a slip joint plier.
4. When finished, inspect for a proper bottom O-ring
seal. This will prevent water leaking into the mount
and perhaps into the vehicle/Machine.
PRECAUTION
The antenna should be mounted on the desired location
before FUNCTIONING. This is to ensure that not damage
antenna during the mounting of the antenna.
IAS_165-00146-002_AA_082014