86B-SCNNF Datasheet, PDF (1/1 Pages) –

ECCOSORB^® 86B Tape & SC-NNF
Neoprene Coated Nylon Fabric for Patching ECCOSORB^® ANW
Material Characteristics
• The ECCOSORB^® 86B Tape and SC-NNF are both made
of the same neoprene coated nylon fabric used to wrap
ECCOSORB^® ANW
• Neither is self-adhesive backed and therefore requires
the use of ECCOSTOCK^® 13-111-NF contact adhesive
for attachment
• Certified to MIL specification: MIL-C-20696E
• Resistant to fuels, lubricants, and hydraulic fluids
• Color is Olive drab
Applications
• ECCOSORB^® 86B Tape is mainly used to reseal rips
and tears in the ECCOSORB^® ANW weatherproofing
cloth as well as reseal the exposed edges of
ECCOSORB^® ANW after being cut for a custom fit
• ECCOSORB^® SC-NNF is a sheet version used for
covering larger areas or complete parts
Availability
• ECCOSORB^® 86B Tape is sold by the roll in 90 foot
lengths. Rolls are available in widths of 2, 3, 4, and 6
inches (5.08, 7.62, 10.2, and 15.2 cm)
• ECCOSORB^® SC-NNF is sold in sheet form by the linear
yard in widths of 58” standard
Instructions for Use
• The recommended adhesive to bond the 86B Tape to
ECCOSORB^® ANW is the ECCOSTOCK^® 13-111-NF
contact adhesive. This adhesive is a one part,
general purpose, non-flammable neoprene adhesive
that is solvent based. ECCOSTOCK^® 13-111-NF
provides good adhesion to urethane foams, wood,
aluminum, rubber, galvanized steel, and most plastics
• All surfaces to be bonded with the ECCOSTOCK^®
13-111-NF should be cleaned to remove all grease,
oil, and foreign materials. A recommended solvent is
Methylene Chloride which should only be used in a
well ventilated area
• ECCOSTOCK^® 13-111-NF may be applied by brush,
roller, or spray equipment
• For spraying, a pressure-type pot spray system is
recommended. A pot pressure of 10 to 15 psi and an
atomization pressure of 80 psi when using a Devilbiss
fluid tip needle type FF will provide acceptable results
• Shake the container well before opening and mix
thoroughly before use
• Coat both surfaces to be bonded with ECCOSTOCK^®
13-111-NF and allow one surface to dry for a period
of time till nearly tack free
• For optimum adhesion it is necessary that one surface
be relatively dry to the touch and the other surface be
tacky at the time when the surfaces are mated
• Allow sufficient overlap of the ECCOSORB^® 86B Tape
and apply sufficient pressure to ensure good contact
of the mating surfaces
EMERSON & CUMING MICROWAVE PRODUCTS, INC., 28 York Avenue, Randolph, MA 02368 / Telephone [phone]. Use of Information and Material: Values shown are based on testing of laboratory test specimens and represent data that
falls within normal range of the material. These values are not intended for use in establishing maximum, minimum or ranges of values for specification purposes. Any determination of the suitability of the material for any purpose
contemplated by the user and the manner of such use is the responsibility of the user. The user should determine that the material meets the needs of the user's product and use. We hope that the information given here will be helpful. It is
based on data and knowledge considered to be true and accurate and is offered for the user's consideration, investigation and verification but we do not warrant the results to be obtained. Please read all statements, recommendations or
suggestions in conjunction with our conditions of sale INCLUDING THOSE LIMITING WARRANTIES AND REMEDIES, which apply to all goods supplied by us. We assume no responsibility for the use of these statements, recommendations or
suggestions nor do we intend them as a recommendation for any use, which would infringe any patent or copyright. Emerson & Cuming Microwave Products Inc.
Revision: 5/11/07
www.eccosorb.com
AA3