|
S6065KTP Datasheet, PDF (5/8 Pages) Littelfuse – 65 / 70 Amp Standard SCRs | |||
|
◁ |
Teccor® brand Thyristors
65 / 70 Amp Standard SCRs
Soldering Parameters
Reï¬ow Condition
1Co'SFFBTTFNCMZ
-Temperature Min (T )
s(min)
Pre Heat -Temperature Max (T )
s(max)
-Time (min to max) (t )
s
Average ramp up rate (Liquidus Temp)
(TL) to peak
T toT - Ramp-up Rate
S(max)
L
Reï¬ow
-Temperature (T ) (Liquidus)
L
-Temperature (t )
L
PeakTemperature (T )
P
Time within 5°C of actual peak
Temperature (t )
p
Ramp-down Rate
Time 25°C to peak Temperature (TP)
Do not exceed
150°C
200°C
oTFDT
5°C/second max
5°C/second max
217°C
oTFDPOET
260+0/-5 °C
oTFDPOET
5°C/second max
8 minutes Max.
280°C
TP
TL
TS(max)
TS(min)
Ramp-up
Preheat
tS
25
time to peak temperature
tP
tL
Ramp-down
Time
Physical Speciï¬cations
Terminal Finish
Body
Lead Material
100% Matte Tin-plated
UL recognized epoxy meeting ï¬ammability
classiï¬cation 94V-0
Copper Alloy
Design Considerations
Careful selection of the correct device for the applicationâs
operating parameters and environment will go a long way
toward extending the operating life of the Thyristor. Good
design practice should limit the maximum continuous
current through the main terminals to 75% of the device
rating. Other ways to ensure long life for a power discrete
semiconductor are proper heat sinking and selection of
voltage ratings for worst case conditions. Overheating,
overvoltage (including dv/dt), and surge currents are
the main killers of semiconductors. Correct mounting,
soldering, and forming of the leads also help protect
against component damage.
Environmental Speciï¬cations
Test
AC Blocking
Temperature Cycling
Temperature/
Humidity
High Temp Storage
Speciï¬cations and Conditions
MIL-STD-750, M-1040, Cond A Applied
Peak AC voltage @ 125°C for 1008 hours
MIL-STD-750, M-1051,
100 cycles; -40°C to +150°C;
15-min dwell-time
EIA / JEDEC, JESD22-A101
1008 hours; 320V - DC: 85°C;
85% rel humidity
MIL-STD-750, M-1031,
1008 hours; 150°C
Low-Temp Storage 1008 hours; -40°C
Thermal Shock
Autoclave
MIL-STD-750, M-1056
10 cycles; 0°C to 100°C; 5-min dwelltime
at each temperature; 10 sec (max) transfer
time between temperature
EIA / JEDEC, JESD22-A102
168 hours (121°C at 2 ATMs) and
100% R/H
Resistance to
Solder Heat
MIL-STD-750 Method 2031
Solderability
ANSI/J-STD-002, category 3, Test A
Lead Bend
MIL-STD-750, M-2036 Cond E
Sxx65x & Sxx70x Series
335
©2013 Littelfuse, Inc
Speciï¬cations are subject to change without notice.
Revised: 09/23/13
|
▷ |