LTC660 Datasheet, PDF (8/12 Pages) Linear Technology – 100mA CMOS Voltage Converter

LTC660
TYPICAL APPLICATIONS N
Negative Voltage Converter
Figure 7 shows a typical connection which will provide a
negative supply from an available positive supply. This
circuit operates over full temperature and power supply
ranges without the need of any external diodes. The LV pin
(Pin 6) is shown grounded, but for V⁺ ≥ 3V, it may be
floated, since LV is internally switched to ground (Pin 3)
for V ⁺ ≥ 3V.
1 _BOOST
V^{+ 8}
2 _CAP+
OSC ⁷
+
C1
150µF
3
LTC660
GND
LV
6
4 _CAP–
V_OUT ⁵
V_IN
1.5V TO 5.5V
V_OUT = –V_IN
C2
150µF
LTC660 • F07
Figure 7. Voltage Inverter
The output voltage (Pin 5) characteristics of the circuit are
those of a nearly ideal voltage source in series with a 6.5Ω
resistor. The 6.5Ω output impedance is composed of two
terms: 1) the equivalent switched-capacitor resistance
(see Theory of Operation), and 2) a term related to the on-
resistance of the MOS switches.
At an oscillator frequency of 10kHz and C1 = 150µF, the
first term is:
( ) ^{REQUIV =}
1₌
f_OSC/2 C1
1
= 1.3Ω.
5 • 10³ • 150 • 10^–6
Notice that the equation for R_EQUIV is not a capacitive
reactance equation (X_C = 1/ωC) and does not contain a
2π term.
The exact expression for output impedance is complex,
but the dominant effect of the capacitor is clearly shown on
the typical curves of output impedance and power effi-
ciency versus frequency. For C1 = C2 = 150µF, the output
impedance goes from 6.5Ω at f_OSC = 10kHz to 110Ω at
f_OSC = 100Hz. As the 1/fC term becomes large compared
to the switch on-resistance term, the output resistance is
determined by 1/fC only.
Voltage Doubling
Figure 8 shows the LTC660 operating in the voltage
doubling mode. The external Schottky (1N5817) diode is
for start-up only. The output voltage is 2 • V_IN without a
load. The diode has no effect on the output voltage.
1N5817*
V_IN
2.5V
TO 5.5V
C1 ⁺
150µF
1 _BOOST
V^{+ 8}
2 _CAP+
OSC ⁷
3
LTC660
GND
LV
6
4 _CAP–
V_OUT ⁵
* SCHOTTKY DIODE IS FOR START-UP ONLY
+
V_OUT = 2V_IN
C2
150µF
LTC660 • F08
Figure 8. Voltage Doubler
Ultraprecision Voltage Divider
An ultraprecision voltage divider is shown in Figure 9. To
achieve the 0.002% accuracy indicated, the load current
should be kept below 100nA. However, with a slight loss
in accuracy, the load current can be increased.
1
8
2
7
+
C1
3
LTC660
6
150µF
4
5
V⁺
2
± 0.002%
T_MIN ≤ T_A ≤ T_MAX
+
I_L ≤ 100nA
C2
150µF
V⁺
3V TO 11V
LTC660 • F09
Figure 9. Ultraprecision Voltage Divider
Battery Splitter
A common need in many systems is to obtain positive and
negative supplies from a single battery or single power
supply system. Where current requirements are small, the
circuit shown in Figure 10 is a simple solution. It provides
symmetrical positive or negative output voltages, both
equal to one-half the input voltage. The output voltages are
both referenced to Pin 3 (Output Common).
8