LTC3202 Datasheet, PDF (8/12 Pages) Linear Technology – Low Noise, High Efficiency Charge Pump for White LEDs

LTC3202
U
OPERATIO
R_OL is dependent on a number of factors including the
switching term, 1/(2f_OSC C_FLY), internal switch resis-
tances and the nonoverlap period of the switching circuit.
However, for a given R_OL, the amount of current available
will be directly proportional to the advantage voltage
1.5V_IN – V_OUT. This voltage can typically be quite small.
Consider the example of driving white LEDs from a
3.1V supply. If the LED forward voltage is 3.8V and the
0.6V V_FB setting is used, the advantage voltage is 3.1V •
1.5V – 3.8V – 0.6V or only 250mV. However if the input
voltage is raised to 3.2V the advantage voltage jumps to
400mV—a 60% improvement in available strength! Note
that a similar improvement in advantage voltage can be
achieved by operating the LTC3202 at a lower voltage
setting such as the 0.4V setting.
V_IN, V_OUT Capacitor Selection
The style and value of capacitors used with the LTC3202
determine several important parameters such as regulator
control loop stability, output ripple, charge pump strength
and minimum start-up time.
To reduce noise and ripple, it is recommended that low
equivalent series resistance (ESR) ceramic capacitors be
used for both C_IN and C_OUT. Tantalum and aluminum
capacitorsarenotrecommendedbecauseoftheirhigh␣ ESR.
The value of C_OUT directly controls the amount of output
ripple for a given load current. Increasing the size of C_OUT
will reduce the output ripple at the expense of higher
minimum turn-on time and higher start-up current. The
peak-to-peak output ripple is approximately given by the
expression:
V_{RIPPLEP−P}
≅ ^IOUT
3f_OSC • C_OUT
Where f_OSC is the LTC3202’s oscillator frequency (typi-
cally 1.5MHz) and C_OUT is the output charge storage
capacitor.
Both the style and value of the output capacitor can
significantly affect the stability of the LTC3202. As shown
in the block diagram, the LTC3202 uses a control loop to
adjust the strength of the charge pump to match the
current required at the output. The error signal of this loop
is stored directly on the output charge storage capacitor.
The charge storage capacitor also serves to form the
dominant pole for the control loop. To prevent ringing or
instability, it is important for the output capacitor to
maintain at least 0.6µF of capacitance over all conditions.
Likewise, excessive ESR on the output capacitor will tend
to degrade the loop stability of the LTC3202. The closed-
loop output resistance of the LTC3202 is designed to be
0.35Ω. For a 100mA load current change, the feedback
voltage will change by about 35mV. If the output capacitor
has 0.35Ω or more of ESR the closed-loop frequency
response will cease to roll-off in a simple one-pole fashion
and poor load transient response or instability could
result. Multilayer ceramic chip capacitors typically have
exceptional ESR performance and combined with a tight
board layout should yield very good stability and load
transient performance.
As the value of C_OUT controls the amount of output ripple,
the value of C_IN controls the amount of ripple present at the
input pin (V_IN). The input current to the LTC3202 will be
relatively constant while the charge pump is on either the
input charging phase or the output charging phase but will
drop to zero during the clock nonoverlap times. Since the
nonoverlap time is small (~25ns) these missing “notches”
will result in only a small perturbation on the input power
supply line. Note that a higher ESR capacitor such as
tantalum will have higher input noise due to the input
current change times the ESR. Therefore ceramic capaci-
tors are again recommended for their exceptional ESR
performance.
Further input noise reduction can be achieved by powering
the LTC3202 through a very small series inductor as
shown in Figure 5. A 10nH inductor will reject the fast
current notches, thereby presenting a nearly constant
current load to the input power supply. For economy the
10nH inductor can be fabricated on the PC board with
about 1cm (0.4") of PC board trace.
3202fa
8