LTC1147-3.3 Datasheet, PDF (8/16 Pages) Linear Technology – High Efficiency Step-Down Switching Regulator Controllers

LTC1147-3.3
LTC1147-5/LTC1147L
APPLICATIO S I FOR ATIO
1000
V_SENSE– = V_OUT = 5V
800
600
400
V_IN = 12V
200 _{VIN = 7V}
V_IN = 10V
0
0
100
200
300
FREQUENCY (kHz)
LTC1147 • F03
Figure 3. Timing Capacitor Value
is given by:
) ^{f ≈}
1
t_OFF
1–
V_OUT
V_IN
where:
) ^tOFF
=
(1.3)(10⁴)(C_T)
V_REG
V_OUT
V_REG is the desired output voltage (i.e., 5V, 3.3V). V_OUT is
the measured output voltage. Thus V_REG/V_OUT = 1 in
regulation.
Note that as V_IN decreases, the frequency decreases.
When the input to output voltage differential drops
below 1.5V, the LTC1147 reduces t_OFF by increasing the
discharge current in C_T. This prevents audible opera-
tion prior to dropout.
Once the frequency has been set by C_T, the inductor L
must be chosen to provide no more than 25mV/R_SENSE
of peak-to-peak inductor ripple current. This results in
a minimum required inductor value of:
L_MIN = (5.1)(10⁵)(R_SENSE)(C_T)(V_REG)
As the inductor value is increased from the minimum
value, the ESR requirements for the output capacitor
are eased at the expense of efficiency. If too small an
inductor is used, the inductor current will become
discontinuous before the LTC1147 series enters Burst
Mode operation. A consequence of this is that the LTC1147
8
series will delay entering Burst Mode operation and effi-
ciency will be degraded at low currents.
Inductor Core Selection
Once the minimum value for L is known, the type of
inductor must be selected. Highest efficiency will be
obtained using ferrite, Kool Mµ^® (from Magnetics, Inc.) or
molypermalloy (MPP) cores. Lower cost powdered iron
cores provide suitable performance but cut efficiency by
3% to 5%. Actual core loss is independent of core size for
a fixed inductor value, but it is very dependent on induc-
tance selected. As inductance increases, core losses go
down. Unfortunately, increased inductance requires more
turns of wire and therefore copper losses will increase.
Ferrite designs have very low core loss, so design goals
can concentrate on copper loss and preventing satura-
tion. Ferrite core material saturates “hard,” which means
that inductance collapses abruptly when the peak design
current is exceeded. This results in an abrupt increase in
inductor ripple current and consequent output voltage
ripple which can cause Burst Mode operation to be
falsely triggered in the LTC1147. Do not allow the core
to saturate!
Kool Mµ is a very good, low loss core material for toroids
with a “soft” saturation characteristic. Molypermalloy is
slightly more efficient at high (>200kHz) switching fre-
quencies but quite a bit more expensive. Toroids are very
space efficient, especially when you can use several
layers of wire. Because they generally lack a bobbin,
mounting is more difficult. However, new designs for
surface mount are available from Coiltronics, Sumida and
Beckman Industrial Corp. which do not increase the
height significantly.
Power MOSFET Selection
An external P-channel power MOSFET must be selected
for use with the LTC1147 series. The main selection
criteria for the power MOSFET are the threshold voltage
V_GS(TH) and “on” resistance R_DS(ON).
The minimum input voltage determines whether a stan-
dard threshold or logic-level threshold MOSFET must be
Kool Mµ is a registered trademark of Magnetics, Inc.
sn1147 1147fds