LTC1502-3.3 Datasheet, PDF (7/8 Pages) Linear Technology – Single Cell to 3.3V Regulated Charge Pump DC/DC Converter

LTC1502-3.3
APPLICATIONS INFORMATION
Short-Circuit Protection
When the output is shorted to ground, the LTC1502-3.3
will continuously charge the C2 capacitor up to approxi-
mately 1.4 times V_IN, and then discharge C2 into the
shorted output. Since the discharging of C2 into V_OUT will
bring the C2 voltage below the COMP2 start-up compara-
tor trip voltage, the output charge pump will be forced
Hi-Z while C2 charges up again. Hence, the internal charge
pump gate drive voltage is limited to (1.4)(V_IN(MAX)) on the
C2 pin, and no continuous current is supplied to V_OUT. The
resulting output short-circuit current is limited to under
20mA (typ) thereby allowing the LTC1502-3.3 to endure
an indefinite output short circuit without damage. When
the short is removed, the part will start up, and operate
normally.
PACKAGE DESCRIPTION Dimensions in inches (millimeters) unless otherwise noted.
MS8 Package
8-Lead Plastic MSOP
(LTC DWG # 05-08-1660)
0.007
(0.18)
0° – 6° TYP
0.021 ± 0.006
(0.53 ± 0.015)
0.040 ± 0.006
(1.02 ± 0.15)
SEATING
PLANE
0.012
(0.30)
REF
0.0256
(0.65)
BSC
0.034 ± 0.004
(0.86 ± 0.102)
0.006 ± 0.004
(0.15 ± 0.102)
* DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
0.118 ± 0.004*
(3.00 ± 0.102)
0.193 ± 0.006
(4.90 ± 0.15)
8 76 5
0.118 ± 0.004**
(3.00 ± 0.102)
MSOP (MS8) 1098
1 234
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.010
(0.254
–
–
0.020
0.508)
×
45°
0.008 – 0.010
(0.203 – 0.254)
0.053 – 0.069
(1.346 – 1.752)
0°– 8° TYP
0.016 – 0.050
(0.406 – 1.270)
0.014 – 0.019
(0.355 – 0.483)
TYP
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
0.004 – 0.010
(0.101 – 0.254)
0.189 – 0.197*
(4.801 – 5.004)
8
7
6
5
0.050
(1.270)
BSC
0.228 – 0.244
(5.791 – 6.197)
0.150 – 0.157**
(3.810 – 3.988)
1
2
34
SO8 1298
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
7