LT1219_15 Datasheet, PDF (7/16 Pages) Linear Technology – Precision Rail-to-Rail Input and Output Op Amps

LT1218/LT1219
ELECTRICAL CHARACTERISTICS
LT1218/LT1219 only; 0°C ≤ T_A ≤ 70°C, V_S = ±15V, V_CM = 0V, V_O = 0V, V_SHDN = 15V, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
I_SC
Short-Circuit Current
I_S
Supply Current
Positive Supply Current, SHDN
V_SHDN = 0V
q
8
17
q
450
q
20
MAX
UNITS
mA
600
µA
54
µA
LT1218, LT1219 only; – 40°C ≤ T_A ≤ 85°C, V_S = ±15V; V_CM = 0V = V_O = 0V, V_SHDN = 15V, unless otherwise noted. (Note 3)
SYMBOL PARAMETER
V_OS
Input Offset Voltage
∆V_OS
I_B
Input Offset Voltage Shift
Input Bias Current
∆I_B
Input Bias Current
I_OS
Input Offset Current
∆I_OS
Input Offset Current Shift
A_VOL
Large-Signal Voltage Gain
CMRR
PSRR
V_OL
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Output Voltage Swing LOW
V_OH
Output Voltage Swing HIGH
I_SC
Short-Circuit Current
I_S
Supply Current
Positive Supply Current, SHDN
CONDITIONS
V_CM = V ⁺ – 0.15
V_CM = V ^– + 0.15
V_CM = V ⁺ – 0.15 to V ^– + 0.15
V_CM = V ⁺ – 0.15
V_CM = V ^– + 0.15
V_CM = V ⁺ – 0.15 to V ^– + 0.15
V_CM = V ⁺ – 0.15
V_CM = V ^– + 0.15
V_CM = V ⁺ – 0.15 to V ^– + 0.15
V_O = – 14.7V to 14.7V, R_L = 10k
V_O = – 10V to 10V, R_L = 2k
V_CM = V ⁺ – 0.15 to V ^– + 0.15
V_S = ±5V to ±15V
No Load
I_SINK = 0.5mA
I_SINK = 2.5mA
No Load
I_SOURCE = 0.5mA
I_SOURCE = 2.5mA
V_SHDN = 0V
MIN
TYP
MAX
UNITS
q
150
600
µV
q
150
600
µV
q
50
165
µV
q
q
– 80
80
nA
nA
q
160
nA
q
40
nA
q
40
nA
q
40
nA
q
500
3000
q
400
1000
V/mV
V/mV
q
105
114
dB
q
96
110
dB
q
V ^– + 0.005 V ^– + 0.015
V
q
V ^– + 0.050 V ^– + 0.105
V
q
V ^– + 0.200 V ^– + 0.620
V
q V⁺ – 0.015 V⁺ – 0.004
V
q V⁺ – 0.160 V⁺ – 0.070
V
q V⁺ – 1.000 V⁺ – 0.400
V
q
5
14
mA
q
650
µA
q
60
µA
The q denotes specifications which apply over the full operating
temperature range.
Note 1: A heat sink may be required to keep the junction temperature
below the Absolute Maximum Rating when the output is shorted
indefinitely.
Note 2: This parameter is not 100% tested.
Note 3: The LT1218/LT1219 are designed, characterized and expected to
meet these extended temperature limits, but are not tested at –40°C and
85°C. Guaranteed I grade part are available: consult factory.
7