LT1054L_15 Datasheet, PDF (7/16 Pages) Linear Technology – Switched-Capacitor Voltage Converter with Regulator

LT1054/LT1054L
Pin Functions
is charging, the peak supply current will be approximately
equal to 2.2 times the output current. During the time that
C_IN is delivering charge to C_OUT the supply current drops
to approximately 0.2 times the output current. An input
supply bypass capacitor will supply part of the peak input
current drawn by the LT1054 and average out the current
drawn from the supply. A minimum input supply bypass
capacitor of 2µF, preferably tantalum or some other low ESR
type is recommended. A larger capacitor may be desirable
in some cases, for example, when the actual input supply
is connected to the LT1054 through long leads, or when
the pulse current drawn by the LT1054 might affect other
circuitry through supply coupling.
Applications Information
Theory of Operation
To understand the theory of operation of the LT1054, a re-
view of a basic switched-capacitor building block is helpful.
In Figure 3 when the switch is in the left position, capaci-
tor C1 will charge to voltage V1. The total charge on C1
will be q1 = C1V1. The switch then moves to the right,
discharging C1 to voltage V2. After this discharge time
the charge on C1 is q2 = C1V2. Note that charge has been
transferred from the source V1 to the output V2. The
amount of charge transferred is:
∆q = q1 – q2 = C1(V1 – V2)
If the switch is cycled f times per second, the charge
transfer per unit time (i.e., current) is:
I = (f)(∆q) = (f)[C1(V1 – V2)]
To obtain an equivalent resistance for the switched-
capacitor network we can rewrite this equation in terms
of voltage and impedance equivalence:
I= ^{V1– V2} = ^{V1– V2}
1/ fC1 R_EQUIV
A new variable R_EQUIV is defined such that R_EQUIV = 1/fC1.
Thus the equivalent circuit for the switched-capacitor
network is as shown in Figure 4. The LT1054 has the same
switching action as the basic switched-capacitor building
block. Even though this simplification doesn’t include finite
switch on-resistance and output voltage ripple, it provides
an intuitive feel for how the device works.
These simplified circuits explain voltage loss as a function
of frequency (see Typical Performance Characteristics).
As frequency is decreased, the output impedance will
V1
V2
f
C1
C2
R_L
LT1054 • F03
Figure 3. Switched-Capacitor Building Block
R_EQUIV
V1
V2
R_EQUIV
=
1
fC1
C2
R_L
LT1054 • F04
Figure 3. Switched-Capacitor Equivalent Circuit
eventually be dominated by the 1/fC1 term and voltage
losses will rise.
Note that losses also rise as frequency increases. This is
caused by internal switching losses which occur due to
some finite charge being lost on each switching cycle. This
charge loss per-unit-cycle, when multiplied by the switching
frequency, becomes a current loss. At high frequency this
loss becomes significant and voltage losses again rise.
The oscillator of the LT1054 is designed to run in the
frequency band where voltage losses are at a minimum.
Regulation
The error amplifier of the LT1054 servos the drive to the
PNP switch to control the voltage across the input capaci-
tor (C_IN) which in turn will determine the output voltage.
Using the reference and error amplifier of the LT1054,
an external resistive divider is all that is needed to set
the regulated output voltage. Figure 5 shows the basic
regulator configuration and the formula for calculating
the appropriate resistor values. R1 should be chosen to
1954lfh
For more information www.linear.com/LT1054
7