RH1499M Datasheet, PDF (5/8 Pages) Linear Technology – 10MHz, 6V/μs, Quad Rail-to-Rail Input and Output Precision C-Load Op Amp

RH1499M
TABLE 2: ELECTRICAL CHARACTERISTICS
(Preirradiation) V_S = 3V, 5V; V_CM = V_OUT = half supply, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
T_A = 25°C
SUB-
NOTES MIN TYP MAX GROUP
GBW Gain-Bandwidth Product V_S = 5V, f = 100kHz
6.8 10.5
SR
Slew Rate
V_S = ±2.5V, A_V = –1,
R_L = 2k,V_O = ±2V,
Measure at V_O = ±1V
2.6 4.5
4
–55°C ≤ T_A ≤ 125°C
MIN TYP MAX
5.8 8.5
2 3.6
SUB-
GROUP UNITS
MHz
5, 6 V/μs
TABLE 2A: ELECTRICAL CHARACTERISTICS
(Postirradiation) V_S = 5V, 3V; V_CM = half supply, T_A = 25°C, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
NOTES
V_OS
Input Offset Voltage V_CM = V⁺, V^–
I_B
Input Bias Current V_CM = V⁺, V^–
I_OS
Input Offset Current V_CM = V⁺, V^–
Input Voltage Range
A_VOL Large-Signal Voltage V_O = 75mV to V⁺ – 0.2V
Gain
R1 = 10k
CMRR Common Mode
Rejection Ratio
V_CM = V⁺ to V^–
CMRR Match
V_CM = V⁺ to V^–
3
(Channel-to-Channel)
10Krad (Si)
MIN MAX
950
700
65
V^– V⁺
300
70
70
20Krad (Si)
MIN MAX
950
750
65
V^– V⁺
300
70
70
PSRR
V_OUT
I_SC
I_S
SR
Power Supply
Rejection Ratio
V_S = 2.2V to 12V,
V_CM = V_O = 0.5V
PSRR Match
V_S = 2.2V to 12V,
(Channel-to-Channel) V_CM = V_O = 0.5V
Output Voltage
Swing Low
No Load
I_SINK = 1mA
I_SINK = 2.5mA
Output Voltage
Swing High
No Load
I_SINK = 1mA
I_SINK = 2.5mA
Short-Circuit Current
Supply Current
Slew Rate
V_S = ±2.5V, A_V = –1,
R_L = 10k, V_O = ±2V,
Measure at V_O = ±1V
88
88
3 82
82
60
60
4
100
100
200
200
20
20
4
150
150
250
250
±8
±8
2.2
2.2
2
2
50Krad (Si)
MIN MAX
950
800
65
V^– V⁺
300
70
70
88
82
60
100
200
20
150
250
±8
2.2
2
100Krad (Si)
MIN MAX
950
850
65
V^– V⁺
300
70
70
88
82
60
100
200
20
150
250
±8
2.2
2
200Krad (Si)
MIN MAX UNITS
950 μV
900 nA
65
nA
V^– V⁺
V
300
V/mV
70
dB
70
dB
88
dB
82
dB
60 mV
100 mV
200 mV
20 mV
150 mV
250 mV
±8
mA
2.2 mA
2
V/μs
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: A heat sink may be required to keep the junction temperature
below this absolute maximum rating when the output is shorted
indefinitely.
Note 3: Matching parameters are the difference between amplifiers A and
D and between B and C.
Note 4: Output voltage swings are measured between the output and
power supply rails.
5