LT1006_02 Datasheet, PDF (5/16 Pages) Linear Technology – Precision, Single Supply Op Amp

LT1006
ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating
temperature range. V_S = ±15V, –55°C ≤ T_A ≤ 125°C, unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS
LT1006AM
LT1006M
MIN TYP MAX MIN TYP MAX UNITS
V_OS
∆V_OS
∆Temp
I_OS
I_B
A_VOL
CMRR
PSRR
I_S
Input Offset Voltage
Input Offset Voltage Drift
Input Offset Current
Input Bias Current
Large-Signal Voltage Gain
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Maximum Output Voltage Swing
Supply Current
V_O = ±10V, R_L = 2k
V_CM = +13V, –14.9V
V_S = ±2V to ±18V, V_O = 0V
R_L = 2k
●
●
●
●
● 0.5
● 97
● 100
● ±12
●
80
0.5
0.2
9
1.5
114
117
±13.8
400
320
110
2.2
0.6
2.0
18
0.25
94
97
±11.5
650
0.3
11
1.0
113
116
±13.8
400
460
µV
2.8 µV/°C
3.0
nA
27
nA
V/µV
dB
dB
V
750
µA
The ● denotes the specifications which apply over the full operating temperature range. V_S = ±15V, 0°C ≤ T_A ≤ 70°C, unless otherwise
noted.
SYMBOL PARAMETER
V_OS
Input Offset Voltage
∆V_OS
∆Temp
Input Offset Voltage Drift
I_OS
I_B
A_VOL
CMRR
PSRR
I_S
Input Offset Current
Input Bias Current
Large-Signal Voltage Gain
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Maximum Output Voltage Swing
Supply Current
CONDITIONS
J8/H Package
N8 Package
S8 Package
J8/H Package
N8 Package
S8 Package
V_O = ±10V, R_L = 2k
V_CM = 13V, –15V
V_S = ±2V to ±18V, V_O = 0V
R_L = 2k
LT1006AC
LT1006C
MIN TYP MAX MIN TYP MAX UNITS
●
50
200
75
300
µV
●
80
330
µV
●
150
730
µV
●
0.5
2.2
●
●
0.6
2.8 µV/°C
0.7
3.5 µV/°C
1.0
4.5 µV/°C
●
0.15
1
0.25
2
nA
●
8
15
10
23
nA
●1
3
0.7
2.5
V/µV
● 98
116
94
114
dB
● 101
120
97
118
dB
● ±12.5 ±13.9
±11.5 ±13.8
V
●
370 600
380
660
µA
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: This parameter is guaranteed by design and is not tested.
Note 3: Regular operation does not require an external resistor. In order
to program the supply current for low power or high speed operation,
connect an external resistor from Pin 8 to Pin 7 or from Pin 8 to Pin 4,
respectively. Supply current specifications (for R_SET = 180k) do not include
current in R_SET.
Note 4: Optional offset nulling is accomplished with a potentiometer
connected between the trim terminals and the wiper to V^–. A 10k pot
(providing a null range of ±6mV) is recommended for minimum drift of
nulled offset voltage with temperature. For increased trim resolution and
accuracy, two fixed resistors can be used in conjunction with a smaller
potentiometer. For example, two 4.7k resistors tied to Pins 1 and 5, with a
500Ω pot in the middle, will have a null range of ±150µV.
1006fa
5