LTC3890 Datasheet, PDF (25/36 Pages) Linear Technology – 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller

LTC3890
APPLICATIONS INFORMATION
resistance losses can be minimized by making sure that
C_IN has adequate charge storage and very low ESR at
the switching frequency. A 25W supply will typically
require a minimum of 20μF to 40μF of capacitance
having a maximum of 20mΩ to 50mΩ of ESR. The
LTC3890 2-phase architecture typically halves this input
capacitance requirement over competing solutions.
Other losses including Schottky conduction losses
during dead-time and inductor core losses generally
account for less than 2% total additional loss.
Checking Transient Response
The regulator loop response can be checked by looking at
the load current transient response. Switching regulators
take several cycles to respond to a step in DC (resistive)
load current. When a load step occurs, V_OUT shifts by
an amount equal to ΔI_LOAD (ESR), where ESR is the ef-
fective series resistance of C_OUT. ΔI_LOAD also begins to
charge or discharge C_OUT generating the feedback error
signal that forces the regulator to adapt to the current
change and return V_OUT to its steady-state value. During
this recovery time V_OUT can be monitored for excessive
overshoot or ringing, which would indicate a stability
problem. OPTI-LOOP compensation allows the transient
response to be optimized over a wide range of output
capacitance and ESR values. The availability of the ITH pin
not only allows optimization of control loop behavior, but
it also provides a DC coupled and AC filtered closed-loop
response test point. The DC step, rise time and settling
at this test point truly reflects the closed-loop response.
Assuming a predominantly second order system, phase
margin and/or damping factor can be estimated using the
percentage of overshoot seen at this pin. The bandwidth
can also be estimated by examining the rise time at the
pin. The ITH external components shown in Figure 13
circuit will provide an adequate starting point for most
applications.
The ITH series R_C-C_C filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
(from 0.5 to 2 times their suggested values) to optimize
transient response once the final PC layout is done and
the particular output capacitor type and value have been
determined. The output capacitors need to be selected
because the various types and values determine the loop
gain and phase. An output current pulse of 20% to 80%
of full-load current having a rise time of 1μs to 10μs will
produce output voltage and ITH pin waveforms that will
give a sense of the overall loop stability without breaking
the feedback loop.
Placing a power MOSFET directly across the output
capacitor and driving the gate with an appropriate signal
generator is a practical way to produce a realistic load step
condition. The initial output voltage step resulting from
the step change in output current may not be within the
bandwidth of the feedback loop, so this signal cannot be
used to determine phase margin. This is why it is better to
look at the ITH pin signal which is in the feedback loop and
is the filtered and compensated control loop response.
The gain of the loop will be increased by increasing R_C
and the bandwidth of the loop will be increased by de-
creasing C_C. If R_C is increased by the same factor that C_C
is decreased, the zero frequency will be kept the same,
thereby keeping the phase shift the same in the most
critical frequency range of the feedback loop. The output
voltage settling behavior is related to the stability of the
closed-loop system and will demonstrate the actual overall
supply performance.
A second, more severe transient is caused by switching
in loads with large (>1μF) supply bypass capacitors. The
discharged bypass capacitors are effectively put in parallel
with C_OUT, causing a rapid drop in V_OUT. No regulator can
alter its delivery of current quickly enough to prevent this
sudden step change in output voltage if the load switch
resistance is low and it is driven quickly. If the ratio of
C_LOAD to C_OUT is greater than 1:50, the switch rise time
should be controlled so that the load rise time is limited
to approximately 25 • C_LOAD. Thus a 10μF capacitor would
require a 250μs rise time, limiting the charging current
to about 200mA.
3890f
25