|
LT1030_15 Datasheet, PDF (2/4 Pages) Linear Technology – Quad Low Power Line Driver | |||
|
◁ |
LT1030
ABSOLUTE MAXIMUM RATINGS
Supply Voltage ...................................................... ±15V
Logic Input Pins ............................................. V â to 25V
On/Off Pin .................................................... GND to 12V
Output (Forced) .............................. V â + 30V, V + â 30V
Short-Circuit Duration (to ±30V) ..................... Indefinite
Operating Temperature Range
Commercial ............................................. 0°C to 70°C
Guaranteed Functional by Design ....... â 25°C to 85°C
Storage Temperature ............................ â 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
PACKAGE/ORDER INFORMATION
Vâ
(â15V TO â5V)
1
2
3
ON/OFF
(0V TO 5V)
4
5
6
GND 7
TOP VIEW
V+
14 (5V TO 15V)
13 STROBE
12
11
10
9
8
N PACKAGE
14-LEAD PDIP
S PACKAGE
14-LEAD PLASTIC SO
TJMAX = 125°C, θJA = 90°C/ W (N)
TJMAX = 125°C, θJA = 95°C/ W (S)
ORDER PART
NUMBER
LT1030CN
LT1030CS
LT1030CJ
CONSULT
FACTORY
Consult factory for Industrial and Military grade parts.
ELECTRICAL CHARACTERISTICS (Supply Voltage = ±5 to ±15V)
PARAMETER
Supply Current
Power Supply Leakage Current
Output Voltage Swing
Output Current
Output Overload Voltage (Forced)
Output Current
Input Overload Voltage (Forced)
Logic Input Levels
Logic Input Current
On/Off Pin Current
Slew Rate
CONDITIONS
VON/OFF ⥠2.4V, IOUT = 0, All Outputs Low
VON/OFF ⤠0.4V
VON/OFF ⤠0.1V
Load = 2mA Positive
Negative
VSUPPLY ± 5V to ±15V
Operating or Shutdown
Shutdown VS = 0V, VOUT = ±30V
VS = ±15V, VOUT = ± 20V
Operating or Shutdown
Low Input (VOUT = High)
High Input (VOUT = Low)
VIN > 2.0V
VIN < 0.8V
0 ⤠VIN ⤠5V
MIN
â
â
V + â 0.3V
5
â
V + â 30V
â
Vâ
â
â
2
â
â10
4
TYP
500
1
10
V + â 0.1V
V â + 0.9V
12
2
2
1.4
1.4
2
10
30
15
MAX
1000
10
150
V â + 1.4V
V â + 30V
100
100
15
0.8
20
20
65
30
UNITS
µA
µA
µA
V
V
mA
V
µA
µA
V
V
V
µA
µA
µA
V/µS
The â denotes specifications which apply over the full operating
temperature range.
Note 1: 3V applied to the Strobe pin will force all outputs low. Strobe pin
input impedance is about 2k to ground. Leave open when not used.
PIN FUNCTIONS
V â(Pin 1): Operates â 15V to â 2V.
LOGIC INPUT (Pins 2, 5, 9, 12): Operate properly on TTL
or CMOS levels. Output valid from (V â + 2V) ⤠VIN ⤠15V.
Connect to 5V when not used.
OUTPUT (Pins 3, 6, 8, 11): Line drive outputs.
ON/OFF (Pin 4): Shuts down entire circuit. Cannot be left
open. For ânormally onâ operation, connect between 5V to
10V.
GND (Pin 7): Ground must be more positive than V â.
STROBE (Pin 13): Forces all outputs low. Drive with 3V.
V + (Pin 14): Positive supply 5V to 15V.
14
8
LT1030
1
7
1N4001
LT1030 ⢠PF01
Note: As with other bipolar ICs, forward biasing the substrate diode can cause
problems. The LT1030 will draw high current from V + to ground if the V â pin is open
circuited or pulled above ground. If this is possible, connecting a diode from V â to
ground will prevent the high current state. Any low cost diode can be used.
2
|
▷ |