LTC3577 Datasheet, PDF (16/52 Pages) Linear Technology – Highly Integrated 6-Channel Portable PMIC

LTC3577/LTC3577-1
PIN FUNCTIONS
N-channel MOS pass transistor. When the voltage on
this pin exceeds a preset level, the OVGATE pin will be
pulled to GND to disable the pass transistor and protect
downstream circuitry.
LED_OV (Pin 9): A resistor between this pin and the boosted
LED backlight voltage sets the overvoltage limit on the
boost output. If the boost voltage exceeds the programmed
limit the LED boost converter will be disabled.
DV_CC (Pin 10): Supply Voltage for I²C Lines. This pin sets
the logic reference level of the LTC3577. A UVLO circuit on
the DV_CC pin forces all registers to all 0s whenever DV_CC
is <1V. Bypass to GND with a 0.1μF capacitor.
SDA (Pin 11): I²C Data Input. Serial data is shifted one bit
per clock to control the LTC3577. The logic level for SDA
is referenced to DV_CC.
SCL (Pin 12): I²C Clock Input. The logic level for SCL is
referenced to DV_CC.
OVGATE (Pin 13): Overvoltage Protection Gate Output.
Connect OVGATE to the gate pin of an external N-channel
MOS pass transistor. The source of the transistor should
be connected to V_BUS and the drain should be connected
to the product’s DC input connector. In the absence of an
overvoltage condition, this pin is connected to an internal
charge pump capable of creating sufficient overdrive to
fully enhance this transistor. If an overvoltage condition
is detected, OVGATE is brought rapidly to GND to prevent
damage. OVGATE works in conjunction with OVSENSE to
provide this protection.
PWR_ON (Pin 14): Logic Input Used to Keep Buck
DC/DCs Enabled After Power-Up. May also be used to
enable the buck DC/DCs directly (sequence = buck1 →
buck2 → buck3). See “Pushbutton Interface Operation”
section for more information.
ON (Pin 15): Pushbutton Input. A weak internal pull-up
forces ON high when left floating. A normally open push-
button is connected from ON to ground to force a low
state on this pin.
PBSTAT (Pin 16): Open-drain output is a de-bounced
and buffered version of ON to be used for processor
interrupts.
16
WAKE (Pin 17): Open-Drain Output. The WAKE pin indicates
the operating state of the buck DC/DCs. If WAKE is Hi-Z, the
BUCK DC/DCs are enabled and either up or powering up.
A low on WAKE indicates that the buck DC/DCs are either
powered down or are powering down. See “Pushbutton
Interface Operation” section for more information.
SW (Pins 18,19,20): Power Transmission (Switch) Pin for
LED Boost Converter. See “LED Backlight/Boost Operation”
section for circuit hook-up and component selection. I²C
is used to control LED driver enable. I²C default is LED
driver off.
PG_DCDC (Pin 21): Open-Drain Output. PG_DCDC goes
high impedance 230ms after all buck DC/DCs are in regula-
tion (within 8% of final value).
I_LED (Pin 22): Series LED Backlight Current Sink Output.
This pin is connected to the cathode end of the series LED
backlight string. The current drawn through the series LEDs
can be programmed via a 6-bit 60dB DAC and dimmed via
an internal 4-bit PWM function. I²C is used to control LED
driver enable, brightness, gradation (soft on/soft off). I²C
default is LED driver off, current = 0mA.
V_INLDO1 (Pin 23): Input Supply of Low Dropout Linear
Regulator 1 (LDO1). This pin should be bypassed to ground
with a 1μF or greater ceramic capacitor.
LDO2_FB (Pin 24): Feedback Voltage Input for Low Drop-
out Linear Regulator 2 (LDO2). LDO2 output voltage is
set using an external resistor divider between LDO2 and
LDO2_FB.
FB2 (Pin 25): Feedback Input for Step-Down Switching
Regulator 2 (Buck 2). This pin servos to a fixed voltage
of 0.8V when the control loop is complete.
FB1 (Pin 26): Feedback Input for Step-Down Switching
Regulator 1 (Buck 1). This pin servos to a fixed voltage
of 0.8V when the control loop is complete.
LDO1_FB (Pin 27): Feedback Voltage Input for Low Drop-
out Linear Regulator 1 (LDO1). LDO1 output voltage is
set using an external resistor divider between LDO1 and
LDO1_FB.
LDO1 (Pin 28): Output of Low Dropout Linear Regulator 1.
This pin must be bypassed to ground with a 1μF or greater
ceramic capacitor.
3577f