|
LT5528 Datasheet, PDF (1/16 Pages) Linear Technology – 1.5GHz to 2.4GHz High Linearity Direct Quadrature Modulator | |||
|
FEATURES
â Direct Conversion to 1.5GHz to 2.4GHz
â High OIP3: 21.8dBm at 2GHz
â Low Output Noise Floor at 5MHz Offset:
No RF: â159.3dBm/Hz
POUT = 4dBm: â151.8dBm/Hz
â 4-Ch W-CDMA ACPR: â66dBc at 2.14GHz
â Integrated LO Buffer and LO Quadrature Phase
Generator
â 50Ω AC-Coupled Single-Ended LO and RF Ports
â 50Ω DC Interface to Baseband Inputs
â Low Carrier Leakage: â42dBm at 2GHz
â High Image Rejection: 45dB at 2GHz
â 16-Lead QFN 4mm à 4mm Package
U
APPLICATIO S
â Infrastructure Tx for DCS, PCS and UMTS Bands
â Image Reject Up-Converters for PCS and UMTS
Bands
â Low-Noise Variable Phase-Shifter for 1.5GHz to
2.4GHz Local Oscillator Signals
LT5528
1.5GHz to 2.4GHz
High Linearity Direct
Quadrature Modulator
DESCRIPTIO
The LT®5528 is a direct I/Q modulator designed for high
performance wireless applications, including wireless
infrastructure. It allows direct modulation of an RF signal
using differential baseband I and Q signals. It supports
PHS, GSM, EDGE, TD-SCDMA, CDMA, CDMA2000,
W-CDMA and other systems. It may also be conï¬gured
as an image reject up-converting mixer, by applying
90° phase-shifted signals to the I and Q inputs. The I/Q
baseband inputs consist of voltage-to-current converters
that in turn drive double-balanced mixers. The outputs of
these mixers are summed and applied to an on-chip RF
transformer, which converts the differential mixer signals
to a 50Ω single-ended output. The four balanced I and Q
baseband input ports are intended for DC coupling from a
source with a common-mode voltage level of about 0.5V.
The LO path consists of an LO buffer with single-ended
input, and precision quadrature generators that produce
the LO drive for the mixers. The supply voltage range is
4.5V to 5.25V.
, LTC and LT are registered trademarks of Linear Technology Corporation.
TYPICAL APPLICATIO
1.5GHz to 2.4GHz Direct Conversion Transmitter Application
with LO Feed-Through and Image Calibration Loop
I-DAC
14
16 V-I
VCC 8, 13
LT5528
5V
RF = 1.5GHz
TO 2.4GHz
W-CDMA ACPR, AltCPR and Noise vs RF Output
Power at 2140MHz for 1, 2 and 4 Channels
â55
â140
DOWNLINK TEST MODEL 64 DPCH
â60
â145
EN
Q-DAC
I-CHANNEL
1
0°
90°
7 Q-CHANNEL
5 V-I
11
PA
4-CH ACPR
â65
2-CH ACPR â150
BALUN
LO FEED-THROUGH CAL OUT
2-CH AltCPR
4-CH AltCPR
IMAGE CAL OUT
â70
1-CH ACPR
â155
1-CH AltCPR
CAL
BASEBAND
DSP
ADC
2, 4, 6, 9, 10, 12, 15, 17
3
VCO/SYNTHESIZER
â75 4-CH NOISE
â160
1-CH NOISE
â80
â165
â42 â38 â34 â30 â26 â22 â18 â14
RF OUTPUT POWER PER CARRIER (dBm)
5528 TA01a
5528 TA01b
5528f
1
|
▷ |