LT2078_15 Datasheet, PDF (1/16 Pages) Linear Technology – Micropower, Dual and Quad, Single Supply, Precision Op Amps

FEATURES
s _{Supply Current per Amplifier: 50µA Max}
s _{Offset Voltage: 70µV Max}
s _{Offset Current: 250pA Max}
s _{Voltage Noise: 0.6µVP-P, 0.1Hz to 10Hz}
s _{Current Noise: 3pAP-P, 0.1Hz to 10Hz}
s _{Offset Voltage Drift: 0.4µV/°C}
s _{Gain Bandwidth Product: 200kHz}
s _{Slew Rate: 0.07V/µs}
s _{Single Supply Operation}
Input Voltage Range Includes Ground
Output Swings to Ground while Sinking Current
No Pull-Down Resistors Needed
s _{Output Sources and Sinks 5mA Load Current}
s _{SO Package with Standard Pinout}
U
APPLICATIONS
s _{Battery or Solar-Powered Systems}
Portable Instrumentation
Remote Sensor Amplifier
Satellite Circuitry
s _{Micropower Sample-and-Hold}
s _{Thermocouple Amplifier}
s _{Micropower Filters}
LT 2078/LT 2079
Micropower, Dual and
Quad, Single Supply,
Precision Op Amps
DESCRIPTION
The LT^®2078 is a micropower dual op amp in 8-pin small
outline, standard surface mount package, and LT2079 is
a micropower quad op amp offered in the standard 14-pin
surface mount package. Both devices are optimized for
single supply operation at 5V. ±15V specifications are also
provided.
Micropower performance of competing devices is achieved
at the expense of seriously degrading precision, noise,
speed and output drive specifications. The design effort of
the LT2078/LT2079 was concentrated on reducing sup-
ply current without sacrificing other parameters. The
offset voltage achieved is the lowest on any dual or quad
nonchopper stabilized op amp––micropower or other-
wise. Offset current, voltage and current noise, slew rate
and gain bandwidth product are all two to ten times better
than on previous micropower op amps.
Both the LT2078/LT2079 can be operated from a single
supply (as low as one lithium cell or two NiCd batteries).
The input range goes below ground. The all NPN output
stage swings to within a few millivolts of ground while
sinking current––no power consuming pull-down resis-
tors are needed. For applications requiring DIP packages
refer to the LT1078/LT1079.
, LTC and LT are registered trademarks of Linear Technology Corporation.
TYPICAL APPLICATION
Single Battery, Micropower, Gain = 100, Instrumentation Amplifier
10.1k
1M
1M
2^–
A
INVERTING 3 ^{+1/2 LT2078}
–INPUT
1 ^10.1k
3V
(Li-Ion)
6– 8
B
NONINVERTING ^{5 +1/2 LT2078}
+INPUT
4
7
OUT
LT2078/79 • TA01
TYPICAL PERFORMANCE
INPUT OFFSET VOLTAGE = 40µV
INPUT OFFSET CURRENT = 0.2nA
OUTPUT NOISE = 85µV_P-P 0.1Hz TO 10Hz
= 300µV_RMS OVER FULL BANDWIDTH
INPUT RANGE = 0.03V TO 1.8V
TOTAL POWER DISSIPATION = 240µW
OUTPUT RANGE = 0.03V TO 2.3V
COMMON MODE REJECTION = 110dB (AMPLIFIER LIMITED)
(0.3mV ≤ V_IN+ – V_IN– ≤ 23mV)
GAIN BANDWIDTH PRODUCT = 200kHz
OUTPUTS SINK CURRENT—NO PULL-DOWN RESISTORS
Distribution of Input Offset Voltage
800
V_S = 5V, 0V
700 ^{5000 OP AMPS}
600
500
400
300
200
100
0
–120
–80 –40 0 40 80
INPUT OFFSET VOLTAGE (µV)
120
2078/79 • TA02
20789fa
1