LT1170 Datasheet, PDF (1/20 Pages) Linear Technology – 100kHz, 5A, 2.5A and 1.25A High Efficiency Switching Regulators

LT1170/LT1171/LT1172
100kHz, 5A, 2.5A and 1.25A
High Efficiency Switching Regulators
FEATURES
DESCRIPTIO
s _{Wide Input Voltage Range: 3V to 60V}
s _{Low Quiescent Current: 6mA}
s _{Internal 5A Switch (2.5A for LT1171,}
1.25A for LT1172)
s _{Shutdown Mode Draws Only 50µA Supply Current}
s _{Very Few External Parts Required}
s _{Self-Protected Against Overloads}
s _{Operates in Nearly All Switching Topologies}
s _{Flyback-Regulated Mode Has Fully Floating Outputs}
s _{Comes in Standard 5-Pin Packages}
s _{LT1172 Available in 8-Pin MiniDIP and Surface Mount}
Packages
s _{Can Be Externally Synchronized}
U
APPLICATIO S
s _{Logic Supply 5V at 10A}
s _{5V Logic to ±15V Op Amp Supply}
s _{Battery Upconverter}
s _{Power Inverter (+ to –) or (– to +)}
s _{Fully Floating Multiple Outputs}
USER NOTE:
This data sheet is only intended to provide specifications, graphs, and a general functional description
of the LT1170/LT1171/LT1172. Application circuits are included to show the capability of the
LT1170/LT1171/LT1172. A complete design manual (AN19) should be obtained to assist in
developing new designs. This manual contains a comprehensive discussion of both the LT1070 and
the external components used with it, as well as complete formulas for calculating the values of these
components. The manual can also be used for the LT1170/LT1171/LT1172 by factoring in the higher
frequency. A CAD design program called SwitcherCAD^TM is also available.
The LT^®1170/LT1171/LT1172 are monolithic high power
switching regulators. They can be operated in all standard
switching configurations including buck, boost, flyback,
forward, inverting and “Cuk.” A high current, high effi-
ciency switch is included on the die along with all oscilla-
tor, control and protection circuitry. Integration of all
functions allows the LT1170/LT1171/LT1172 to be built in
a standard 5-pin TO-3 or TO-220 power package as well as
the 8-pin packages (LT1172). This makes them extremely
easy to use and provides “bust proof” operation similar to
that obtained with 3-pin linear regulators.
The LT1170/LT1171/LT1172 operate with supply volt-
ages from 3V to 60V, and draw only 6mA quiescent
current. They can deliver load power up to 100W with no
external power devices. By utilizing current-mode switch-
ing techniques, they provide excellent AC and DC load and
line regulation.
The LT1170/LT1171/LT1172 have many unique features
not found even on the vastly more difficult to use low
power control chips presently available. They use adaptive
antisat switch drive to allow very wide ranging load cur-
rents with no loss in efficiency. An externally activated
shutdown mode reduces total supply current to 50µA
typically for standby operation.
, LTC and LT are registered trademarks of Linear Technology Corporation.
SwitcherCAD is a trademark of Linear Technology Corporation.
TYPICAL APPLICATIO
Boost Converter (5V to 12V)
5V
L1**
50µH
L2 _OUTPUT
10µH _FILTER
+
C3*
100µF
V_IN
V_SW
LT1170
FB
GND
V_C
R3
1k
C1
1µF
D1
MBR330
C3
100µF
+
C2
1000µF
12V
R1 ^1A
10.7k
1%
R2
1.24k
1%
*REQUIRED IF INPUT LEADS ≥ 2" ** COILTRONICS 50-2-52
PULSE ENGINEERING 92114
1170/1/2 TA01
Maximum Output Power*
100
LT1170
80
60
BOOST
40
BUCK-BOOST
V_O = 30V
FLYBACK
* ROUGH GUIDE ONLY. BUCK MODE
P_OUT = (5A)(V_OUT)
SPECIAL TOPOLOGIES DELIVER
MORE POWER.
** DIVIDE VERTICAL POWER SCALE
BY TWO FOR LT1171, BY FOUR
FOR LT1172.
LT1170/1/2 TA02
20
BUCK-BOOST
V_O = 5V
0
0
10
20
30
40
50
INPUT VOLTAGE (V)
1