LT8611 Datasheet, PDF (9/24 Pages) Linear Technology – 42V, 2.5A Synchronous Step-Down Regulator

LT8611
PIN FUNCTIONS
SYNC (Pin 1): External Clock Synchronization Input.
Ground this pin for low ripple Burst Mode operation at low
output loads. Tie to a clock source for synchronization to
an external frequency. Apply a DC voltage of 3V or higher
or tie to INTV_CC for pulse-skipping mode. When in pulse-
skipping mode, the I_Q will increase to several hundred μA.
Do not float this pin.
TR/SS (Pin 2): Output Tracking and Soft-Start Pin. This
pin allows user control of output voltage ramp rate during
start-up. A TR/SS voltage below 0.97V forces the LT8611
to regulate the FB pin to equal the TR/SS pin voltage. When
TR/SS is above 0.97V, the tracking function is disabled
and the internal reference resumes control of the error
amplifier. An internal 2.2μA pull-up current from INTV_CC
on this pin allows a capacitor to program output voltage
slew rate. This pin is pulled to ground with an internal 230Ω
MOSFET during shutdown and fault conditions; use a series
resistor if driving from a low impedance output. This pin
may be left floating if the tracking function is not needed.
RT (Pin 3): A resistor is tied between RT and ground to
set the switching frequency.
EN/UV (Pin 4): The LT8611 is shut down when this pin
is low and active when this pin is high. The hysteretic
threshold voltage is 1.00V going up and 0.96V going
down. Tie to V_IN if the shutdown feature is not used. An
external resistor divider from V_IN can be used to program
a V_IN threshold below which the LT8611 will shut down.
V_IN (Pins 5, 6): The V_IN pins supply current to the LT8611
internal circuitry and to the internal topside power switch.
These pins must be tied together and be locally bypassed.
Be sure to place the positive terminal of the input capaci-
tor as close as possible to the V_IN pins, and the negative
capacitor terminal as close as possible to the PGND pins.
PGND (Pins 7, 8): Power Switch Ground. These pins are
the return path of the internal bottom-side power switch
and must be tied together. Place the negative terminal of
the input capacitor as close to the PGND pins as possible.
NC (Pins 9, 10, 11, 12): No Connect. These pins are not
connected to internal circuitry. It is recommended that
these be connected to GND so that the exposed pad GND
can be run to the top level GND copper to enhance thermal
performance.
SW (Pins 13, 14, 15): The SW pins are the outputs of the
internal power switches. Tie these pins together and con-
nect them to the inductor and boost capacitor. This node
should be kept small on the PCB for good performance.
BST (Pin 16): This pin is used to provide a drive voltage,
higher than the input voltage, to the topside power switch.
Place a 0.1μF boost capacitor as close as possible to the IC.
INTV_CC (Pin 17): Internal 3.4V Regulator Bypass Pin.
The internal power drivers and control circuits are pow-
ered from this voltage. INTV_CC maximum output cur-
rent is 20mA. Do not load the INTV_CC pin with external
circuitry. INTV_CC current will be supplied from BIAS if
V_BIAS > 3.1V, otherwise current will be drawn from V_IN.
Voltage on INTV_CC will vary between 2.8V and 3.4V when
V_BIAS is between 3.0V and 3.6V. Decouple this pin to power
ground with at least a 1μF low ESR ceramic capacitor
placed close to the IC.
BIAS (Pin 18): The internal regulator will draw current from
BIAS instead of V_IN when BIAS is tied to a voltage higher
than 3.1V. For output voltages of 3.3V and above this pin
should be tied to V_OUT. If this pin is tied to a supply other
than V_OUT use a 1μF local bypass capacitor on this pin.
PG (Pin 19): The PG pin is the open-drain output of an
internal comparator. PG remains low until the FB pin is
within ±9% of the final regulation voltage, and there are
no fault conditions. PG is valid when V_IN is above 3.4V,
regardless of EN/UV pin state.
FB (Pin 20): The LT8611 regulates the FB pin to 0.970V.
Connect the feedback resistor divider tap to this pin. Also,
connect a phase lead capacitor between FB and V_OUT.
Typically, this capacitor is 4.7pF to 10pF.
ISP (Pin 21): Current Sense (+) Pin. This is the noninvert-
ing input to the current sense amplifier.
ISN (Pin 22): Current Sense (–) Pin. This is the inverting
input to the current sense amplifier.
8611p
9