CP2000AC54TEP Datasheet, PDF (4/20 Pages) Lineage Power Corporation – 100-120/200-277VAC input; Default Outputs: ±54VDC @ 2000W, 5VDC @ 4W

GE
Data Sheet
CP2000AC54TE CPL High Efficiency Rectifier
100-120/200-277VAC input; Default Outputs: ±54VDC @ 2000W, 5VDC @ 4W
5VDC Auxiliary output
Parameter
Output Voltage Setpoint
Overall Regulation
Output Current
Ripple and Noise (20mHz bandwidth)
Over-voltage Clamp
Over-current Limit
Isolation from the main output STD / POE compliant
Isolation from frame ground
Symbol
VOUT
Min
-10⁷
0.005
110
500 / 2250
50
Typ
5
50
Max
+5
0.75
100
7
175
Unit
VDC
%
A
mVp-p
VDC
%FL
Vdc
Vdc
General Specifications
Parameter
Reliability
Service Life
Unpacked Weight
Packed Weight
Heat Dissipation
Min
Typ
Max
Units
Notes
450,000
Hours
Full load, 25C ; MTBF per SR232 Reliability protection for
electronic equipment, issue 2, method I, case III,
10
Years Full load, excluding fans
2.18/4.8
Kgs/Lbs
2.45/5.4
Kgs/Lbs
100 Watts or 341 BTUs @ 80% load, 153 Watts or 522 BTUs @ 100% load
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Signals are referenced
to Logic_GRD unless noted otherwise. Fault, PFW, OTW, SMBAlert#, and Power capacity need to be pulled HI through external pull-up resistors. See
Feature Descriptions for additional information.
Parameter
Symbol
Min
Typ
Max
Unit
Enable (should be connected to Logic_GRD) 54V output OFF
54V output ON
Margining (through adjusting Vcontrol)
Voltage control range
Programmed output voltage range
Voltage adjustment resolution (8-bit A/D)
Output configured to 54VDC
Output configured to 44VDC
ON/OFF [short pin controls 54VDC output - ] referenced to VOUT( - )
54V output OFF
54V output ON
Module Present [Resistor connected to Logic_GRD internally]
Write protect enabled
Write protect disabled
Over Temperature Warning (OTW) Logic HI (temperature normal)
Sink current
Logic LO (temperature is too high)
Fault Logic HI (No fault is present)
Sink current
Logic LO (Fault is present)
SMBAlert# (Alert#_0, Alert#_1) Logic HI (No Alert - normal)
Sink current
Logic LO (Alert is set)
VOUT
1.4

VOUT
0

44
Vcontrol
0
VOUT
42
Vcontrol
3.3
Vcontrol
3.0
Vcontrol
0
Vcontrol
1.4

Vcontrol
0

500
V
1

V
0

V
0.7VDD

I


V
0

V
0.7VDD

I


V
0

V
0.7VDD

I


V
0

5
VDC
0.8
VDC
58
VDC
3.3
VDC
58
VDC
mVDC
3. 3
VDC
0.1
VDC
5
VDC
0.8
VDC
Ω
5
VDC
0.8
VDC
12
VDC
5
mA
0.4
VDC
12
VDC
5
mA
0.4
VDC
12
VDC
5
mA
0.4
VDC
7 _{Within ±5% when load is < 0.5A}
August 16, 2013
©2013 General Electric Company. All rights reserved.
Page 4