HAH1DR200-S Datasheet, PDF (3/5 Pages) LEM – AUTOMOTIVE CURRENT TRANSDUCER

Absolute maximum ratings
Parameter
Symbol
Max primary current peak
I_Pmax
Supply continuous over voltage
Reverse voltage ²⁾
V_C
Output over voltage (continuous)
V_OUT
Continuous output current
I_OUT
Output short-circuit duration
T_c
Rms voltage for AC isolation test
V_d
Isolation resistance
R_IS
Electrostatic discharge voltage
V_ESD
Ambient storage temperature
T_S
Operating characteristics
Parameter
Symbol
Primary current
Calibration current
Supply voltage
Output voltage (Analog) ³⁾
Sensitivity ³⁾
Current consumption
Load resistance
Output internal resistance
Capacitive loading
Ambient operating temperature
Output drift versus power supply
I_P
I_CAL
V_C
V_OUT
G
I_C
R_L
R_OUT
C_L
T_A
V_{OUT PS}
Sensitivity error
Electrical offset current
Magnetic offset current
Global offset current
Average temperature coefficient of V_OE
Average temperature coefficient of G
Linearity error
Response time to 90 % of I_PN step
Frequency bandwidth ⁴⁾
Output clamping voltage min
Output clamping voltage max
Output voltage noise peak-peak
ε
G
I_OE
I_OM
I_O
TCV_{OE AV}
TCG _AV
ε
L
t_r
BW
V_sz
V_sz
V_{no pp}
HAH1DR 200-S
Unit
Specification
Min
Typ
Max
Electrical Data
Conditions
A
1)
V
-0.5
V
-0.5
mA
-10
7
V_C + 0.5
10
Not operating
1 min @ T_A = 25°C
min
2
kV
2
50 Hz, 1 min
MΩ
500
500 V - ISO 16750-2
kV
2
JESD22-A114-B
°C
-55
125
Unit
A
A
V
V
mV/A
mA
ΚΩ
Ω
nF
°C
%
%
A
mV/°C
%/°C
%
µs
kHz
V
V
mV
Specification
Min
Typ
Max
Electrical Data
-200
200
-200
200
4.75
5.00
5.25
V_OUT = (V_C/5) X (2.5 + G X I_P)
10
15
20
10
10
1
100
-40
125
0.5
Performance Data
-1.0
± 0.5
1.0
± 0.6
± 0.9
-1.5
1.5
-0.08
± 0.03
0.08
-0.035
± 0.02
0.035
-1
1
6
10
30
0.1
4.9
22
Conditions
@ T_A = 25°C
@ V_C
@ V_C = 5 V
@ V_C = 5 V, @ - 40°C < T_A < 125°C
DC to 1 kHz
Connector limited 105°C
@ T_A = 25°C @ I = I_P
@ T_A = 25°C, @ V_C = 5 V
@ T_A = 25°C, @ V_C = 5 V, after ± I_P
@ T_A = 25°C
@ - 40°C < T° < 125°C
@ - 40°C < T° < 125°C
@ V_C = 5 V @, T_A = 25°C, @ I = I_P
@ di/dt = 100 A/µs
@ -3 dB
@ V_C = 5 V, T_A = 25°C
@ V_C = 5 V, T_A = 25°C
DC to 1MHz
Notes:
1) _{Busbar temperature must be below 150°C}
2) _{Transducer not protected against reverse polarity.}
3) _{The output voltage VOUT is fully ratiometric. The offset and sensitivity are dependent on the supply voltage VC}
relative to the following formula:
IP   VOUT  ^VC   ¹  ⁵

2 _ G VC
with G in (V / A)
4) _{Tested only with small signal only to avoid excessive heating of the magnetic core.}
090707/2
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
Page 3/5
www.lem.com