HXS20-NP_12 Datasheet, PDF (1/3 Pages) LEM – Current Transducer

Current Transducer HXS 20-NP
For the electronic measurement of currents: DC, AC, pulsed...,
with galvanic isolation between the primary circuit (high power)
and the secondary circuit (electronic circuit).
I_PN = 5-10-20 A
All Data are given with a R_L = 10 kΩ
Electrical data
I_PN
I_PM
V_OUT
G_TH
V_REF
R_L
R_OUT
C_L
V_C
I_C
Primary nominal current rms
Primary current, measuring range
Analog Output voltage @ I_P
Theoretical sensitivity
Reference voltage ¹⁾ Ouput voltage
Ouput impedance
Load impedance
Load resistance
Output internal resistance
Capacitive loading (± 20 %)
Supply voltage (± 5 %) ²⁾
Current consumption @ V_C = 5V
± 20
A
± 60
A
V_OE ± (0.625. I_P/ I_PN) V
0.625
V/ I_PN
2.5 ± 0.025
V
typ. 200
Ω
≥ 200
kΩ
≥ 2
kΩ
< 5
Ω
= 4.7
nF
5
V
19
mA
Accuracy - Dynamic performance data
X
ε
L
Accuracy ³⁾ @ I_PN , T_A = 25°C
Linearity error
0 .. I_PN
0 .. 3 x I_PN
TCV_OE Temperature coefficient of V_OE
(+25.. 105°C)

(-40.. +25°C)
TCV_REF Temperature coefficient of V_REF

(+25.. 105°C)
(-40.. +25°C)
TCV_OE/V_REFTemperature coefficient of V_OE /V_REF
TCG Temperature coefficient of G
V_OE
V_OM
t_ra
t_r
di/dt
Electrical offset voltage @ I_P = 0, T_A = 25°C
Magnetic offset voltage @ I_P = 0
after an overload of 3 x I_PN
Reaction time to 10 % of I_PN step
Response time to 90 % of I_PN step
di/dt accurately followed
V_no
Output voltage noise (DC .. 10 kHz)
(DC .. 1 MHz)
BW
Frequency bandwidth (- 3 dB) ⁴⁾
≤ ± 1
%
≤ ± 0.5
%
≤ ± 1
%
≤ ± 0.4
mV/K
≤ ± 0.525
mV/K
≤ ± 0.01
%/K
≤ ± 0.015
%/K
≤ ± 0.15
mV/K
≤ ±0.05% of reading//K
V_REF ± 0.0125
V
< ± 0.7
< 3
< 5
> 50
< 20
< 40
DC .. 50
%
µs
µs
A/µs
mVpp
mVpp
kHz
General data
T_A
Ambient operating temperature ⁵⁾
T_S
Ambient storage temperature
m
Mass
Standards
- 40 .. + 105
°C
- 40 .. + 105
°C
10
g
EN 50178: 1997
Features
●● Hall effect measuring principle
●● Multirange current transducer
through PCB pattern lay-out
●● Galvanic isolation between
primary and secondary circuit
●● Isolation test voltage 3500 V
●● Low power consumption
●● Extremely low profile < 11 mm
●● Single power supply + 5 V
●● Fixed offset & sensitivity
●● Isolated plastic case recognized
according to UL 94-V0.
Advantages
●● Small size and space saving
●● Only one design for wide current
ratings range
●● High immunity to external
interference
●● Internal & external reference.
Applications
●● AC variable speed drives and
servo motor drives
●● Static converters for DC motor
drives
●● Battery supplied applications
●● Uninterruptible Power Supplies
(UPS)
●● Switched Mode Power Supplies
(SMPS)
●● Power supplies for welding
applications.
Notes:
1)_{It is possible to overdrive VREF with an external reference voltage between 1.5V -}
2.8V providing its ability to sink or source approximately 5 mA.
Application domain
2)_{Maximum supply voltage (not operating) < 6.5 V}
3)_{Excluding Offset and Magnetic offset voltage}
●● Industrial.
4)_{Small signal only to avoid excessive heatings of the magnetic core.}
5)_{UL recognized with surrounding temperature until +85℃}
Page 1/3
120416/21
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
www.lem.com