HTB50-TP Datasheet, PDF (1/2 Pages) LEM – Current Transducers HTB 50~400-P and HTB 50~100-TP

Current Transducers HTB 50 .. 400-P
and HTB 50 .. 100-TP
For the electronic measurement of currents: DC, AC, pulsed, mixed,
with a galvanic isolation between the primary circuit (high power) and
the secondary circuit (electronic circuit).
I = 50 .. 400 A
PN
Electrical data
Primary nominal
r.m.s. current
I_PN (A)
50
100
200
300
400
Primary current
measuring range
I_P (A)
±150
±300
±500
±600
±600
Type
HTB 50-P, HTB 50-TP¹⁾
HTB 100-P, HTB 100-TP¹⁾
HTB 200-P
HTB 300-P
HTB 400-P
V_C
I_C
V
d
R_IS
V_OUT
R_OUT
R_L
Supply voltage (±5 %) ²⁾
±12 .. ±15 V
Current consumption
<±15
mA
R.m.s. voltage for AC isolation test, 50/60 Hz, 1 mn 2.5
kV
Isolation resistance @ 500 VDC
>500
MΩ
Output voltage @ ± I_PN, R_L = 10 kΩ, T_A = 25°C
±4
V
Output internal resistance
100
Ω
Load resistance
≥10
kΩ
Accuracy - Dynamic performance data
X
ε
L
V
OE
V_OH
V_OT
ε TC _G
t_r
f
Accuracy @ I_PN, T_A = 25°C (without offset)
Linearity (0 .. ± I )
PN
Electrical offset voltage, T = 25°C
A
Hysteresis offset voltage @ I_P = 0;
after an excursion of 3 x I
PN
Thermal drift of V_OE HTB 50-(T)P
HTB 100-(T)P..400-P
Thermal drift (% of reading)
Response time @ 90% of I_P
Frequency bandwidth (0..-3 dB) ³⁾
<±1
<±1
<±30
% of I_PN
% of I
PN
mV
<±1 % of I
PN
<±2.0 mV/K
<±1.0 mV/K
<±0.1 %/K
<3
µs
DC .. 50 kHz
General data
T_A
Ambient operating temperature
T
Ambient storage temperature
S
m
Mass (-TP version)
-20 .. +80 °C
-25 .. +85 °C
<30 (<36) g
2 pins of Ø2mm diameter are available on transducer
for PCB soldering.
Features
• Hall effect measuring principle
• Galvanic isolation between primary
and secondary circuit
• Isolation voltage 2500V
• Low power consumption
• Wide power supply: ±12V to ±15V
• Primary bus bar option for 50A and
100A version for ease of connection
Advantages
• Small size and space saving
• Only one design for wide current
ratings range
• High immunity to external
interference.
Applications
• AC variable speed drives
• Static converters for DC motor drives
• Battery supplied applications
• Uninterruptible Power Supplies
(UPS)
• Switched Mode Power Supplies
(SMPS)
• Power supplies for welding
applications.
Notes : EN 50178 approval pending
1) _{-TP version is equipped with a primary bus bar.}
2) _{Operating at ±12V ≤ Vc < ±15V will reduce measuring range.}
3) _{Derating is needed to avoid excessive core heating at high frequency.}
040720/9
LEM Components
www.lem.com