ML13156 Datasheet, PDF (1/21 Pages) LANSDALE Semiconductor Inc. – Wideband FM IF System

ML13156
Wideband FM IF System
Legacy Device: Motorola MC13156
The ML13156 is a wideband FM IF subsystem targeted at high per-
formance data and analog applications. The ML13156 has an onboard
grounded collector VCO transistor that may be used with a fundamen-
tal or overtone crystal in single channel operation or with a PLL in
multichannel operation. The mixer is useful to 500 MHz and may be
used in a balanced–differential, or single–ended configuration. The IF
amplifier is split to accommodate two low cost cascaded filters. RSSI
output is derived by summing the output of both IF sections. A preci-
sion data shaper has a hold function to preset the shaper for fast recov-
ery of new data.
Applications for the ML13156 include CT–2, wideband data links
and other radio systems utilizing GMSK, FSK, or FM modulation.
• 2.0 to 6.0 Vdc Operation
• Typical Sensitivity at 200 MHz of 2.0 µV for 12 dB SINAD
• RSSI Dynamic Range Typically 80 dB
• High Performance Data Shaper for Enhanced CT–2 Operation
• Internal 330 Ω and 1.4 kΩ Terminations for 10.7 Mhz and 455 kHz
Filters
• Split IF for Improved Filtering and Extended RSSI Range
• 3rd Order Intercept (Input) of –25 dBm (Input Matched)
• Operating Temperature Range – TA = –40 to +85°C
Simplified Block Diagram
LO LO
CAR
DS Data DS DS
Quad
In Emit VEE1 Det RSSI VEE2 Hold Out Gnd In Demod Coil
24 23 22 21 20 19 18 17 16 15 14 13
Mixer
Bias
Data
Slicer
5.0
pF
Bias
IF Amp
LIM Amp
1
2
3
4
5
6
7
8
9
10 11 12
RF RF Mix VCC1 IF
IF
IF
IF VCC2 LIM LIM LIM
In 1 In 2 Out
In DEC 1 DEC 2 Out
In DEC 1 DEC 2
NOTE: Pin Numbers shown for SOIC package only. Refer to Pin Assignments Table.
This device contains 197 active transistors.
Page 1 of 21
www.lansdale.com
24
1
SO 24W = -6P
PLASTIC PACKAGE
CASE 751E
(SO-24L)
QFP 32 = -8P
32
PLASTIC QFP PACKAGE
CASE 873
1
CROSS REFERENCE/ORDERING INFORMATION
PACKAGE MOTOROLA LANSDALE
SO 24W
QFP 32
MC13156DW
MC13156FB
ML13156-6P
ML13156-8P
Note: Lansdale lead free (Pb) product, as it
becomes available, will be identified by a part
number prefix change from ML to MLE.
PIN CONNECTIONS
Function
SO–24L
RF Input 1
1
RF Input 2
2
Mixer Output
3
VCC1
4
IF Amp Input
5
IF Amp Decoupling 1
6
IF Amp Decoupling 2
7
VCC Connect (N/C Internal)
–
IF Amp Output
8
VCC2
9
Limiter IF Input
10
Limiter Decoupling 1
11
Limiter Decoupling 2
12
VCC Connect (N/C Internal)
–
Quad Coil
13
Demodulator Output
14
Data Slicer Input
15
VCC Connect (N/C Internal)
–
Data Slicer Ground
16
Data Slicer Output
17
Data Slicer Hold
18
VEE2
19
RSSI Output/Carrier Detect In
20
Carrier Detect Output
21
VEE1 and Substrate
22
LO Emitter
23
LO Base
24
VCC Connect (N/C Internal)
–
QFP
31
32
1
2
3
4
5
6
7
8
9
10
11
12, 13, 14
15
16
17
18
19
20
21
22
23
24
25
26
27
28, 29, 30
Issue A